TABLE OF CONTENTS
Our Thank You | 2 |
|
Cautions and Advisories | 2 |
|
Signal Sensing Feature | 3 |
|
Specifications | 4 - 5 | |
Adjustments and Installation: |
|
|
T500W/2 | 6 - 7 | |
T1000W/2 | 8 - 9 | |
T2000W/4 | 10 | - 11 |
T2000WD/1 (Mono Class D) | 12 | - 13 |
TD5X (Full Range + Mono Class D) | 14 | - 15 |
THANK YOU
Thank you for choosing Earthquake Sound’s line of TNT amplifier: the best way to enhance your factory mobile audio system. With proper installation and responsible listening, your amplifier(s) will give you years of near perfect sound reproduction.
We strongly recommend you to have your new amplifier(s) installed by an authorized Earthquake Sound dealer. Installation professionals employed by your dealer have the correct tools and knowledge to install your amplifier(s) neatly and successfully. Also, when your new products are installed by an authorized dealer, your product will include a FIVE (5) YEAR LIMITED
SIGNAL SENSING FEATURE - AUTO ON/REMOTE ON
This TNT amplifier features the new, improved and more powerful circuitry. Better yet, Earthquake Sound has added a special AUTO SIGNAL SENSING Feature which allows installers to turn on the amplifier without using the remote wire.
By simply connecting the RCA or Speaker level inputs to the amplifier, it will turn on automatically when it senses an audio signal. This feature makes upgrading the sound system in many of the latest model vehicles easier for installers as it eliminates the need to connect a remote turn on wire to the amplifier.
Before you proceed, please note the following:
!This feature may not be compatible with all latest model vehicles.
!If your vehicle is going to be parked for over 4 weeks, then you should disconnect the main fuse of the amplifier.
!Be sure to follow the connection instructions and illustrations below.
AUTO ON
When the switch is on AUTO ON, the amplifier will automatically detect an incoming signal when the stereo is turned on. If the amplifier does not detect any signal after 20 minutes, the amplifier will automatically turn off.
The proper power and remote wire connection when using the AUTO SIGNAL SENSING is illustrated below.
WARRANTY. If you choose to perform your own installation, your warranty will be subject to limitations. Dealer policies on handling warranty requests may vary from one dealer to the next.
Please read the warranty information in its entirety and use good judgment when making these vital decisions.
|
|
| POWER |
|
| |
| GND |
| REM | BAT |
| |
|
|
|
| (+) |
| |
|
|
|
|
|
|
|
to battery
| unit |
to | head |
|
| POWER |
|
GND | REM | BAT |
| (+) |
to battery
CAUTION: Earthquake Amplifiers are capable of generating high sound pressure levels. You should exercise caution when operating these amplifier systems. Long term exposures to high
levels of sound pressure will cause permanent damage to your hearing. Sound pressure levels exceeding 85dB can be dangerous with constant exposure. Set your audio system to a comfortable loudness level. Earthquake Sound Corporation does not assume liability for damages resulting from the direct use of Earthquake amplifiers or other Earthquake products and urges users to play their music at moderate listening levels.
SOUND LEVEL DBA | DURATION IN HOURS | THE CHART (ON THE SIDE) SHOWS THE U.S. | |
90 | 8 |
| |
| GOVERNMENTS OCCUPATIONAL SAFETY AND | ||
92 | 6 |
| |
| H E A L T H A D M I N I S T R A T I O N ( O S H A ) | ||
95 | 4 |
| |
| REGULATIONS WHICH WERE IN EFFECT AT | ||
97 | 3 |
| THE TIME OF THIS PUBLICATION FOR |
100 | 2 |
| PERMISSIBLE NOISE EXPOSURE, PER |
102 | 1 - | 1 1/2 | 29CFR1910.95, TABLE |
105 | 1 |
|
|
110 | 1/2 |
|
|
115 | 1/4 | or less |
|
DO NOT connect the remote wire to the head unit as this will damage your sound system.
RESET
In case the system goes into protection, simply turn off the audio source, lower the volume and slide the switch to RESET then back to AUTO ON position.
REMOTE ON
When the switch is on REMOTE ON, the amplifier relies on the remote wire to detect the signal and turn the amplifier on or off.
NOTE: RCA outputs must be inserted in CH1/2 for the amplifier to detect any incoming signal.
2 |
|
| 3 |
Specifications Are Subject To Change Without Notice | www.earthquakesound.com |