Earthquake Sound T1000W/2, TD5X, T500W/2, T2000WD/1, T2000W/4 40Hz 100Hz 180Hz 280Hz 360Hz 400Hz

TD5X

This information applies to both channels 1/2 and 3/4

SUB INPUT:		SUB XOVER:	MODE SELECTOR:			LEVEL ADJUST:		VARIABLE XOVER:	LOW INPUTS:
This is	your	The 0-18dB/Oct	This feature tells the			Control the max output of		C o n t r o l t h e	These are CH1/2(FRONT)
s u b w o o f e r		Xover provides	amplifier to		run in	each channel. The LEVEL		corresponding channels'	& 3/4(REAR) low inputs
channel	where	control over the	either	HIGH	PASS,	controls	its respective	cutoff frequencies. This	with a range of 0.2V to
the sub	RCA	device cutoff	FULL	RANGE or		channel	regardless how	feature is disabled when	7V RMS. This is where
outputs	from	frequency.	LOW PASS MODE			many inputs in use.		in FULL RANGE.	the front and rear RCA
your head unit									outputs from your head
are inserted.									unit are inserted.

SUBWOOFER CONTROL

CHANNEL 1/2 CONTROL

CHANNEL 3/4 CONTROL

L

L

L

GAIN

XOVER REMOTE

MODE

GAIN

XOVER

MODE

GAIN

XOVER

2

4

MIN MAX 40 160

HP

FR

LP

MIN MAX

40 400

HP FR

LP MIN MAX

40

400

AUTO ON RESET REMOTE ON

1

3

INPUT SELECTOR

R

5

4

2

R

R

CHANNEL 1/2 SIGNAL FLOW

MONO CHANNEL 5 SIGNAL FLOW

CHANNEL 3/4 SIGNAL FLOW

LEVEL ADJUST:

REMOTE

INPUT SELECTOR:

AUTO SIGNAL

Allows the amplifier to deliver a		SUB		This tells the amp to play all channels even if only one pair of			SENSING:
controlled maximum sound		LEVEL:		RCAs is connected. EXAMPLE: If the head unit only has one			Please	refer to
level into selected channel(s)		Allows you to		pair of RCA outputs then you must plug them into the CH1/2			p a g e	3	f o r
when the volume is turned to		adjust	amps	connections and set the switch to 2. This tells the amp that you			explanation of this
max. This acts as a volume		bass	output	are using one set of RCAs and it needs to play all five channels			feature.
l i m i t e r f o r	t h e s y s t e m ,	i n t e n s i t y		regardless. If you have four RCAs, then set it to 4 and so on.
preventing you from over		remotely.
driving the	speakers or
subwoofers.
				SUB
				XOVER
				SETTING
				TD5X	40Hz	100Hz 180Hz 280Hz 360Hz 400Hz

	MAX INPUT
The gain knob is not a volume control.	VOLTAGE
It is designed to match the input level of	BEFORE
the amp to the output level of the source	CLIPPING
unit. Over driving "clipping" the input
stage of the amp will cause damage to the	RCA LEVEL	7.0V	4.0V	2.5V	1V
amplifier (please refer to table for setting).

	CH1/2
Set Xover to desired setting and set Mode
switch to HIGH (high-pass). Level	40Hz 400Hz MIN MAX
adjustment should be dialed in by ear. Keep	HIGH FULL LOW
	XOVER LEVEL
it at MIN and slowly work your way up.

FC6.2 FC6.2

Tweeter Tweeter

FC6.2 Mid-Range FC6.2 Mid-Range

FC6.2 Xover FC6.2 Xover

FRONT		REAR		SUB
CH1-	CH2+	CH3-	CH4+	-
CH1+	CH2-	CH3+	CH4-	+
CH1-	CH2+	CH3-	CH4+	CH5-

CH1+ CH2- CH3+ CH4- CH5+

CH1+ CH2- CH3+ CH4-

BRIDGED BRIDGED

OUTPUT

Three 25A fuses

GND REMOTE +12V

POWER

FUSES

25A 25A 25A

PROT

PWR

PROTECTION (PROT) LED:

If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details.

FRONT		REAR		SUB
CH1-	CH2+	CH3-	CH4+	-
CH1+	CH2-	CH3+	CH4-	+

CH1+ CH2- CH3+ CH4-

BRIDGED BRIDGED

OUTPUT

Focus EQ-693 Focus EQ-693 The Sub Channel Will Accept

2 or 4-Ohm Subwoofers

CH3/4

Set Xover switch to FULL (full range)

40Hz 400Hz MIN MAX

HIGH FULL LOW

XOVER LEVEL

To car chassis / ground

To remote turn on / trigger

POWER (PWR) LED:	Bridgeable speaker outputs,
When LED is on, it indicates that the	minimum 4-Ohms, plus
amplifier is ON and functioning properly.	subwoofer connection.

To battery positive (+)

14			15
	Specifications Are Subject To Change Without Notice	www.earthquakesound.com