Clarion DMX5555Z owner manual Troubleshooting, TV Operations Manual tuning Auto store, Off

TV Operations

Manual tuning Auto store

8. TROUBLESHOOTING

There are 2 ways available: Quick tuning and step tuning.

When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the desired frequency.

1.Press BAND button ! and select the desired band (TV1 or TV2).

∗If “MANU” is not lit in the display, press and hold BAND button ! for 1 second or longer. “MANU” lights in the display and manual tun- ing is now available.

2.Tune into a station.

●Quick tuning:

Press and hold Right button ¥ or Left button

%for 1 second or longer to quickly tune up and down to a desired station.

●Step tuning:

Press Right button ¥ or Left button % to manually tune to a station, one channel at a time.

Recalling a preset station

Atotal of 12 TV stations can be stored (6-TV1 and 6-TV2). This allows you to select your favorite TV stations and store them in memory for later recall.

1.Press BAND button ! and select the desired TV band (TV1 or TV2).

2.To recall a stored TV station, press the desired Preset button 1 to select that station.

∗Press and hold one of the Preset buttons 1 for 2 seconds or longer to store the current sta- tion into the preset memory.

Manual memory

1.Select the desired station with seek tuning, manual tuning or preset tuning.

2.Press and hold one of the Preset buttons 1 for 2 seconds or longer to store the current station to that preset memory.

Auto store selects 6 TV stations automatically and stores each one into a preset memory.

If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory.

1.Press BAND button ! and select the desired TV band (TV1 or TV2).

2.Press and hold AS button 5 for 2 seconds or longer. The stations with good reception are automatically stored to the Preset buttons 1.

Preset scan

Preset scan allows the user to view each preset position before it automatically advances to the next preset. This function is useful for searching for a desired TV station in memory.

1.Press PS button 5.

2.When a desired station is found, press PS button 5 again to remain tuned to that sta- tion.

Note:

•Do not press and hold PS button 5 for 2 seconds or longer. Doing so will trigger the auto store function and start storing stations into memory.

Setting the receiver for Diversity tuning

You can change the reception setting for the TV antenna connected to the TV tuner.

∗The factory default setting is “ON”.

1.Press and hold ADJ button # for 1 second or longer to switch to the adjustment selection display.

2.Press Right button ¥ or Left button % to se- lect “TV DIVER”.

3.Press Up button & to set to “ON” or Down button * to set to “OFF”.

ON:

In the “ON” position, the TV tuner emphasizes the visual signal by choosing the antenna with the best signal strength. This requires more than one antenna on the vehicle.

OFF:

Set the TV Diver adjustment to the “OFF” po- sition when only using one antenna on the vehicle.

4.Press ADJ button # to return to the previous mode.

	Problem	Cause		Measure
	Power does not	Fuse is blown.	Replace with a fuse of the same amperage. If the
	turn on.		fuse blows again, consult your store of purchase.
	(No sound is
		Incorrect wiring.	Consult your store of purchase.
	produced.)
	No sound output	Power antenna lead is	1. Turn the unit off.
	when operating	shorted to ground or	2. Remove all wires attached to the power antenna
	the unit with	excessive current is required	lead. Check each wire for a possible short to
	amplifiers or	for remote-on the amplifiers	ground using an ohm meter.
	power antenna	or power antenna.	3. Turn the unit back on.
	attached.		4. Reconnect each amplifier remote wire to the
			power antenna lead one by one. If the amplifiers
General			turn off before all wires are attached, use an
			external relay to provide remote-on voltage
			(excessive current required).
	Nothing happens	The microprocessor has	Press the reset button with a thin rod.
	when buttons are	malfunctioned due to noise,
	pressed.	etc.		Reset button
	Display is not
	accurate.

	CD cannot be	Another CD is already	Eject the CD before loading the new one.
	loaded.	loaded.
	Sound skips or is	CD is dirty.	Clean the CD with a soft cloth.
	noisy.
CD		CD is heavily scratched or	Replace with a CD with no scratches or no warped.
		warped.
	Sound is bad	Water droplets may form on	Let it dry for about 1 hour with the power on.
	directly after	the internal lens when the
	power is turned	car is parked in a humid
	on.	place.
	MD cannot be	Another MD is already	Eject the MD before loading the new one.
	loaded.	loaded.
	MD is immediately	MD inserted wrongly.	Insert correctly.
	ejected.
		Non-recorded MD is loaded.	Replace with a pre-recorded MD.
MD
	Sound skips or is	MD is heavily scratched or	Replace with an MD with no scratches or no warped.
	noisy.	warped.
	Sound is bad	Water droplets may form on	Let it dry for about 1 hour with the power on.
	directly after	the internal lens when the
	power is turned	car is parked in a humid
	on.	place.

22 DMX5555z

DMX5555z 23

280 7323 00 280 7323 00