CAUTION
Be sure to lower the volume before switch- ing off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit.
Turning on/off the power
Note:
•Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery.
Adjusting the volume
Turning the [ROTARY] knob clockwise in- creases the volume; turning it counterclockwise decreases the volume.
∗The volume level is from 0 (minimum) to 33 (maxi- mum).
Switching the display
Press the [D] button to select the desired display.
Each time you press the [D] button, the display switches in the following order:
Main display
• IMPACT | : bass and treble empha- |
| sized |
• EXCITE | : bass and treble empha- |
| sized mid de-emphasized |
• CUSTOM | : user custom |
• Z+ OFF | : no sound effect |
Adjusting the tone
Press the [A-M] button and select the item to adjust. Each time you press the [A-M] button, the item changes as following order:
● When “B-BOOST” is set |
“B-BOOST” ➜ “BAL 0” ➜ “FAD 0” ➜ Last |
function mode. |
● When “IMPACT” is set |
Adjusting the treble (Gain, Frequency)
This adjustment can be performed when the Z- Enhancer Plus is set to “CUSTOM”.
1. | Press the [A-M] button and select “TREBLE”. |
2. | Turning the [ROTARY] knob clockwise em- |
| phasizes the treble; turning it counterclock- |
| wise attenuates the treble. |
| ∗ The factory default setting is “T<G 0>”. (Ad- |
| justment range: –6 to +6) |
3. | Press the [d] or [a] button to select |
| “T<F 10>”. |
| Turninng the [ROTARY] knob clockwise or |
1.Press the [FNC] button.
2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.
3.Press and hold the [FNC] button for 1 sec- ond or longer to turn off the power for the unit.
Note:
•System check
The first time this unit is turned on after the wire connections are completed, it must be checked what equipment is connected. When the power is turned on, “SYSTEM” and “PUSH PWR” appear in the display alternately, so press the [FNC] but- ton. The system check starts within the unit. When the system check is complete, press the [FNC] button again.
Selecting a mode
1. | Press the [FNC] button to change the opera- |
| tion mode. |
2. | Each time you press the [FNC] button, the |
Sub display
Clock display
Main display
∗ Once selected, the preferred display becomes |
the display default. When a function adjust- |
ment such as volume is made, the screen will |
momentarily switch to that function’s display, |
then revert back to the preferred display sev- |
eral seconds after the adjustment. |
∗ When you have entered a title in a CD, it ap- |
pears in the sub display. If you have not en- |
tered a title, “NO TITLE” appears in the title |
display instead. For information on how to en- |
ter a title, refer to the subsection “Entering |
“IMPACT” ➜ “BAL 0” ➜ “FAD 0” ➜ Last |
function mode. |
● When “EXCITE” is set |
“EXCITE” ➜ “BAL 0” ➜ “FAD 0” ➜ Last |
function mode. |
● When “CUSTOM” is set |
“BASS” ➜ “TREBLE” ➜ “BAL 0” ➜ “FAD |
0” ➜ Last function mode. |
● When “Z+ OFF” is set |
“BAL 0” ➜ “FAD 0” ➜ Last function mode. |
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can be performed when the Z- Enhancer Plus is set to “CUSTOM”.
1.Press the [A-M] button and select “BASS”.
2.Turning the [ROTARY] knob clockwise em- phasizes the bass; turning it counterclock- wise attenuates the bass.
∗The factory default setting is “B<G 0>”. (Ad- justment range: –6 to +6)
counterclockwise to select the frequency. |
∗ The factory default setting is “T<F 10>”.(Ad- |
justment 10 kHz/15 kHz) |
4. When the adjustment is complete, press the |
[A-M] button several times until the function |
mode is reached. |
Adjusting the balance
1.Press the [A-M] button and select “BAL 0”.
2.Turning the [ROTARY] knob clockwise em- phasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker.
∗The factory default setting is “BAL 0”. (Adjust- ment range: L13 to R13)
3.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FAD 0”.
operation mode changes in the following or- |
der: |
Radio mode ➜ CD mode ➜ CD changer |
mode ➜ MD changer mode ➜ DVD changer |
mode ➜ TV mode ➜ AUX mode ➜ Radio |
mode... |
∗ External equipment not connected with |
CeNET is not displayed. |
titles” in section “Operations Common to |
Each Mode”. |
Setting the Z-Enhancer Plus
This unit are provided with 3 types of sound tone ef- fects stored in memory. Select the one you prefer.
∗The factory default setting is “Z+ OFF”.
Each time you press the [Z+] button, the tone ef- fect changes in the following order:
3.Press the [d] or [a] button to select “B<F 60>”.
Turninng the [ROTARY] knob clockwise or counterclockwise to select the frequency.
∗The factory default setting is “B<F 60>”.(Ad- justment 60/100/200 Hz)
4.Press the [d] or [a] button to select “B<Q 1>”.
Turninng the [ROTARY] knob clockwise or counterclockwise to select the Q-curve.
2.Turning the [ROTARY] knob clockwise em- phasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers.
∗The factory default setting is “FAD 0”. (Adjust- ment range: F12 to R12)
3.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.
