Clarion DXZ735MP owner manual Basic Operations

7. OPERATIONS

Basic Operations

English

Basic Operations	Note: Be sure to read this chapter referring to the front diagrams of
	chapter “3. CONTROLS” on page 5 (unfold).

“Z+ OFF” ➜ “BASS BOOST” ➜ “IMPACT” ➜

“EXCITE” ➜ “CUSTOM” ➜ “Z+ OFF” ...

• BASS BOOST : bass emphasized

Adjusting the bass (Gain,

Frequency, Q-curve)

This adjustment can be performed when the Z-

English

CAUTION

Be sure to lower the volume before switch- ing off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sud- den loud volume may hurt your hearing and

Adjusting the volume

Turning the [ROTARY] knob clockwise increases the volume; turning it counterclockwise de- creases the volume.

∗The volume level is from 0 (minimum) to 33 (maxi- mum).

• IMPACT	: bass and treble empha-
	sized
• EXCITE	: bass and treble empha-
	sized mid de-emphasized
• CUSTOM	: user custom
• Z+ OFF	: no sound effect

Enhancer Plus is set to “CUSTOM”.

1.Press the [A-M] button and select “BASS”.

2.Turning the [ROTARY] knob clockwise em- phasizes the bass; turning it counterclock- wise attenuates the bass.

∗The factory default setting is “BÅGAIN 0Δ. (Adjustment range: –6 to +8)

damage the unit.

Turning on/off the power

Note:

•Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery.

Switching the display

Press the [D] button to select the desired display.

Each time you press the [D] button, the display switches in the following order:

Main display

Adjusting the Z-Enhancer Plus

1.	Press the [Z+] button and select the Z-En-
	hancer Plus mode to adjust.
2.	Press the [A-M] button and turning the
	[ROTARY] knob clockwise adjusts in the +
	direction; tuning it counterclockwise adjusts
	in the – direction.
	● When “B-BOOST 0” selected, you can ad-
	just the bass in the range of –3 to 3.

3.	Press the [d] or [a] button to select
	“BÅFREQ 50Δ.
	Turninng the [ROTARY] knob clockwise or
	counterclockwise to select the frequency.
	∗ The factory default setting is “BÅFREQ 50Δ.
	(Adjustment 50/80/120 Hz)
4.	Press the [d] or [a] button to select “BÅQ 1Δ.
	Turninng the [ROTARY] knob clockwise or
	counterclockwise to select the Q-curve.

1.Press the [FNC] button.

2.The illumination and display on the unit light up. The unit automatically remembers its last operation mode and will automatically switch to display that mode.

3.Press and hold the [FNC] button for 1 second or longer to turn off the power for the unit.

Note:

•System check

The first time this unit is turned on after the wire connections are completed, it must be checked what equipment is connected. When the power is turned on, “SYSTEM CHK” and “Push POWER” appear in the display alternately, so press the [FNC] button. The system check starts within the unit. When the system check is complete, press the [FNC] button again.

Selecting a mode

1.Press the [FNC] button to change the opera- tion mode.

2.Each time you press the [FNC] button, the operation mode changes in the following or- der:

Radio mode ➜ CD/MP3/WMA mode ➜ CD changer mode ➜ MD changer mode ➜ DVD changer mode ➜ TV mode ➜ AUX mode ➜ Radio mode...

∗External equipment not connected with CeNET is not displayed.

Clock display

Main display

∗Once selected, the preferred display becomes the display default. When a function adjust- ment such as volume is made, the screen will momentarily switch to that function’s display, then revert back to the preferred display sev- eral seconds after the adjustment.

∗When you have entered a title in a CD, it ap- pears in the main display. If you have not en- tered a title, “NO TITLE” appears in the title display instead. For information on how to en- ter a title, refer to the subsection “Entering titles” in section “Operations Common to Each Mode”.

Setting the Z-Enhancer Plus

This unit are provided with 3 types of sound tone ef- fects stored in memory. Select the one you prefer.

∗The factory default setting is “Z+ OFF”.

Each time you press the [Z+] button, the tone ef- fect changes in the following order:

● When “IMPACT 0” selected, you can adjust

the bass and treble in the range of –3 to 3.

● When “EXCITE 0” selected, you can adjust

the bass and treble in the range of –3 to 3.

∗When Z-Enhancer Plus is selected, press and hold the [Z+] button for 1 second or longer to change to the “CUSTOM” mode.

Bass/treble characteristics become flat and the indication “Z+FLAT” is shown in the dis- play.

Adjusting the tone

Press the [A-M] button and select the item to adjust. Each time you press the [A-M] button, the item changes as following order:

●When “BASS BOOST” is set “B-BOOST” ➜ “BAL 0” ➜ “FADER 0” ➜

Last function mode.

●When “IMPACT” is set

“IMPACT” ➜ “BAL 0” ➜ “FADER 0” ➜ Last function mode.

●When “EXCITE” is set

“EXCITE” ➜ “BAL 0” ➜ “FADER 0” ➜ Last function mode.

●When “CUSTOM” is set

“BASS” ➜ “TREBLE” ➜ “BAL 0” ➜ “FADER 0” ➜ Last function mode.

●When “Z+ OFF” is set

“BAL 0” ➜ “FADER 0” ➜ Last function mode.

∗ The factory default setting is “BÅQ 1Δ.

(Adjustment 1/1.25/1.5/2)

5. When the adjustment is complete, press the

[A-M] button several times until the function

mode is reached.

Adjusting the treble (Gain,

Frequency)

This adjustment can be performed when the Z- Enhancer Plus is set to “CUSTOM”.

1.Press the [A-M] button and select “TREBLE”.

2.Turning the [ROTARY] knob clockwise em- phasizes the treble; turning it counterclock- wise attenuates the treble.

∗The factory default setting is “TÅGAIN 0Δ. (Adjustment range: –6 to +6)

3.Press the [d] or [a] button to select “TÅFREQ 12KΔ.

Turninng the [ROTARY] knob clockwise or counterclockwise to select the frequency.

∗The factory default setting is “TÅFREQ 12KΔ. (Adjustment 8 kHz/12 kHz)

4.When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

12 DXZ735MP DXZ735MP 13