Alesis RA300, RA150 manual Importance of Speaker Polarity, Output Connections for Bridged Operation

Page 22

Connections: Chapter 2

THE IMPORTANCE OF SPEAKER POLARITY

The speaker cone’s motion should mimic the instrument it’s reproducing. For example, a kick drum pushes air toward you on the initial transient, so a speaker reproducing a kick drum should have its cone push air toward you. If the polarity is reversed, the cone will suck air away from you. Even though the same amount of air is moved in either case, many listeners report superior sound with proper polarity as opposed to reversed polarity.

An additional problem occurs if the polarity of one speaker is reversed with respect to the other. This can cause phase-related problems such as thin bass, poor stereo imaging and frequency response anomalies.

With the RA150/300/500, polarity is a function of correctly hooking up the output cables. Usually, for proper polarity, the tip of the output phone plug or the red terminal of the output connector must connect to the speaker’s positive (+) terminal. This will ensure that polarity from the RA150/300/500 input to speaker cone motion will be consistent. Check your speakers' polarity, however, because not all brands follow this wiring convention.

Please note that polarity reversal can occur in devices (such as mixers or effects units) “upstream” of the RA150/300/500. To test for proper speaker and system polarity, see page 22.

OUTPUT CONNECTIONS FOR BRIDGED OPERATION

Instead of using the RA150/300/500 as a stereo 2- channel amplifier, it is possible to use it as a mono amplifier with twice the power. This uses both sides of the amplifier in a push-pull configuration, so the speaker must be wired to the amp differently.

However, note that the minimum load impedance is 8 ohms, instead of the 4 ohms in stereo operation.

To connect a speaker in bridged mono mode:

Following the instructions on the previous page for binding post or crimp-on connection, connect the "+" wire to the red binding post for the Channel 1/Left and the "-" wire to the red binding post for Channel 2/Right.

You may use a dual banana plug in this situation. If present, remove the protective caps from the top of the binding posts for the two red terminals. Plug the banana connector into the two center red terminals with the ridged/GND side on Channel 2/Right.

The single input is connected ONLY to the Channel 1/Left input jack, and the stereo/mono switch under the right input connector should be set to BRIDGED MONO. Don't plug any input into the Channel 2/Right input jack, and leave the Channel 2 volume control all the way down.

Should you use bridged mode?

In a typical PA system with two speakers, in most cases you'll be better off running the RA150/300/500 in stereo mode, because most speakers are 8 ohms and if they were wired in parallel the total load would be 4 ohms, too low for bridged mode. In any case, the total system volume doesn't rise if you were to connect 2 speakers to a single 500-watt amp instead of to two 250-watt amps.

But if you are connecting to a single speaker (such as a subwoofer) in a biamped or triamped setup, bridged mono mode will give you the chest- thumping headroom you need.

20

RA150/300/500 Reference Manual

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Power Amplifiers Reference SeriesAlesis Contact Information Contents HOW to USE this Manual IntroductionImportant Safety Instructions Safety Symbols Used in this ProductSymboles Utilisés Dans CE Produit Instructions DE Sécurité Importantes FrenchLesen Sie die Hinweise CE Declaration of Conformity EMCPrincipal Features Reference Series Features About this ManualConnections Power ConsiderationsAC Cord and Grounding VOLT/230 Volt Operation Electrical Service toFuse Operating Environment Temperature Considerations in Rack MountingOther Rack Mounting Tips Mounting on a Shelf or in a NON-RACK Enclosure Avoiding Electromagnetic InterferenceInput Jack Characteristics InputsBalanced wiring of an XLR input Connector To use an unbalanced source with an Alesis amplifierCable Wiring Tips CablesTo connect a balanced line output to feed the RA150/300/500 Balanced or UNBALANCED?To connect an unbalanced source to the amplifier input To use the amplifier in Bridged Mono mode To feed the same source to several different amplifiersWhats the Load IMPEDANCE? ConnectorsOutputs Speaker CablesConnecting Speaker Cables to Binding Posts To connect speaker cable to the connectorsOutput Connections for Bridged Operation To connect a speaker in bridged mono modeImportance of Speaker Polarity Should you use bridged mode?Mute Switch ON-OFF SwitchVolume Controls OperationBack Panel Controls Meters RA300 and RA500Checking for Proper Polarity Using the RA150 AS a Headphone Amplifier Choosing the Correct SpeakersDevice a Shielded cable Path Device B To AC power service About Ground LoopsSystem Setup and Testing Setting the Gain ProperlyAmplifier input clipping Output RELAYS/THERMAL CyclingTroubleshooting Troubleshooting IndexCleaning Care and MaintenanceRefer ALL Servicing to Alesis Obtaining Repair Service Customers Outside the USA and CanadaSpecifications ReferenceDimensioned drawings RA300 RA500 Architects and Engineers Specifications Index Alesis Limited Warranty Please Register Your Product OnlineWarranty

RA150, RA500, RA300 specifications

The Alesis RA series of amplifiers—comprising the RA300, RA500, and RA150—have earned a respected spot in the audio equipment landscape, catering to both musicians and audio professionals. With a blend of innovative technology, robust performance, and user-friendly features, these amplifiers offer solutions for various sound requirements.

Starting with the RA300, this amplifier delivers a solid output of 150 watts per channel at 4 ohms, making it ideal for smaller studio setups or personal listening environments. It is built with a lightweight yet durable design, employing a modern Class AB architecture that ensures low distortion and high audio fidelity. The RA300 features comprehensive input options, including balanced XLR and quarter-inch TRS inputs, allowing seamless integration into diverse setups. Additionally, the built-in protection circuitry prevents overheating and damage during prolonged use, ensuring longevity and reliability.

The RA500 steps up the power and performance, presenting a robust 250 watts per channel at 4 ohms, making it suitable for larger venues and demanding applications. It utilizes advanced thermal management technology, which aids in efficient heat dissipation, ensuring the amplifier operates smoothly even under heavy load. The RA500 also boasts significant dynamic range and headroom, making it a preferred choice for professional environments where audio clarity and volume are paramount. The addition of a frequency response that spans from 20Hz to 20kHz means it can faithfully reproduce a wide range of audio frequencies.

Meanwhile, the RA150 serves as a versatile option for various applications, delivering 75 watts per channel at 4 ohms. Despite its compact size, the RA150 does not compromise on sound quality or functionality. Its Class AB amplifier technology results in enhanced audio accuracy, making it popular among beginner studios and educational settings. The straightforward controls and indicators ensure that users can quickly adjust settings for optimal performance.

All three amplifiers in the Alesis RA series share a common goal: to provide high-quality sound amplification without unnecessary complexity. Their combination of solid construction, advanced technologies, and thoughtful features make them suitable for a multitude of audio environments—from home studios to professional gigs. Whether you opt for the RA300, RA500, or RA150, you are investing in a reliable tool designed to deliver exceptional audio performance, catering to the needs of discerning audiophiles and professionals alike.
Top Page Image Contents