Arcam AVP700 manual Before making connections, Zone 2 explained, Audio, Video

Page 5

Before making connections

Before connecting your equipment it is important to think about the following points, as these will affect your choice of connections and subsequent use of the system.

Audio

Wherever possible, connect both the analogue and digital outputs of digital sources. This enables use of a digital input for the main zone with the corresponding analogue input used for recording onto an analogue tape deck or VCR, or for the Zone 2 output.

Video

The AVP700 allows for conversion between different analogue video formats. This means that the AVP700 can convert between composite, S-video and component, if required.

For example, if you are watching a composite input from a VCR, you may view it from the S-video or Component/RGB video outputs of the AVP700. This allows you to use a single (typically high-quality Component/RGB) connection between the AVP700 and your display device. Neither the record loops nor Zone 2 work from the video converter, however. This means that to record a S-video or composite signal, a S-video or composite signal (respectively) must be supplied; to view video in Zone 2, a composite signal is required.

The analogue video quality hierarchy is as follows:

<Component/RGB – highest

<S-video – middle

<Composite – lowest

If all the video inputs are connected simultaneously from one device, e.g., a DVD player, the AVP700 will select automatically the best format available.

English

HDMI

The AVP700 is fitted with two HDMI inputs and one HDMI output, allowing switching of HDMI signals. The AVP700 does not perform conversion between analogue audio/video and HDMI, but does allow an HDMI input to be associated with a particular source, so that selecting the source selects the associated HDMI input.

HDMI signals cannot be routed to Zone 2. If you are using an HDMI connection and you wish to have the same audio and video in Zone 2, then you will need additionally to provide analogue audio and video connections (as described above).

Zone 2

A line-level signal from the stereo analogue audio together with the composite video inputs are available for Zone 2. The analogue inputs from source components are required because the AVP700 provides no analogue-to-digital, DSP processing or digital-to-analogue conversion; the composite video connections are required since the AVP700 does not perform video format conversion for Zone 2.

For these reasons, we recommend that source devices that have a digital connection are also connected to the analogue inputs. High quality YUV/RGB and S-video sources should also have their composite outputs connected to the AVP700 for use in Zone 2.

Zone 2 explained

As well as routing audio and video signals to your main listening/viewing area, your AVP700 is capable of routing the same, or different, signals to a second location (a kitchen, bedroom or study, for example). This second location is called ‘Zone 2’.

HDMI (High Definition

Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, digital TV, set-top boxes, etc. HDMI was developed to combine the technologies of High-bandwidth Digital Content Protection (HDCP) and the Digital Visual Interface (DVI) in one specification, with the addition of transmission of digital audio information; HDCP is used to protect digital content transmitted to DVI-compliant displays.

Although we have tried to make it as simple as possible, installation of the AVP700 for use with Zone 2 is usually quite complicated, principally because there are often several different ways of reaching the same goal. This flexibility means that the AVP700 will, almost certainly, be able to work in the way that you require, but some planning will be necessary.

If you wish to use a Zone 2, we recommend that you read the “Installation” section of this handbook thoroughly before beginning, in order to understand all the options available to you. If you have any questions, please contact your dealer: he will be happy to offer advice and assistance.

AVP700

E-5

Image 5
Contents Arcam AVP700 Pre-amp. processor Safety compliance Safety guidelinesImportant safety instructions Contents Inserting the batteries into the remote control Using this handbookBefore you start IntroductionZone 2 explained Before making connectionsAudio VideoPositioning the unit InstallationAVP700 rear panel CablesAnalogue audio connections Audio connectionsAnalogue pre-amplifier outputs Connection of record decksComposite/S-video video connections Video connectionsComponent video connections Important notes about HQ-video inputs and outputsZone 2 connections Scart RGB 4-WIRE ConnectionControl connections Connecting the AM and FM antennasConnecting to a power supply Set-up mode Configuring the AVP700Set-up Menu Index Navigating the Set-up menuSelect Cvbs status General Settings‘Basic’ Set-up Menus Surr L/R Small Large Sub woofer SettingsSpeaker Sizes Distance measurements for 5.1 Speaker Delay SettingsSpeaker delay settings EX Settings Level settingsADV 3 Digital Settings ADV 2 Video Settings‘Advanced’ Set-up Menus ADV 1 Speaker EqADV 4 Zone 2 Settings Saving Settings and Exit Set-upADV 5 Analogue Settings ADV 6 Hdmi SettingsRemote control Volume control Switching on/offOperating your AVP700 Front panel displayInput selection HeadphonesStereo Direct ZoneEffects/FX Remote control buttonsMode Treble/BassUsing the tuner Using the remote control to enter the Main Menu Using the Main MenuUsing the front panel to enter the Main Menu Listening to the tuner in ZoneEffect Display Centre spreadingDigital multi-channel sources Surround modesFollowing decoding and surround modes are available Mono Two-channel source modesMulti-channel source modes DSP Effects Modes Speaker positioningTroubleshooting No Zone 2 audio when playing DTS film Source switching changes randomly or freezes on one sourceUnable to adjust bass and treble controls Sound is poor or distortedIR Remote Codes Command Command codeSystem code Command Command code Scart S-video cable with audio back to processor Scart connectionsScart RGB cable with audio back to processor Radio interference Technical specificationsContinual improvement policy On line registration GuaranteeWorldwide Guarantee
Related manuals
Manual 43 pages 3.92 Kb