LG Electronics 32LT777H Cracking noise a cracking noise that, Varies depending on the product

			IMPORTANT SAFETY INSTRUCTIONS 5
yyGenerated Sound		For USA and Canada
	“Cracking” noise: A cracking noise that
	occurs when watching or turning off the TV		FCC NOTICE
	is generated by plastic thermal contraction	This equipment has been tested and found
	due to temperature and humidity. This noise
		to comply with the limits for a Class B digital
	is common for products where thermal
		device, pursuant to Part 15 of the FCC Rules.
	deformation is required.
		These limits are designed to provide reasonable
	Electrical circuit humming/panel buzzing: A
		protection against harmful interference in
	low level noise is generated from a high-
		a residential installation. This equipment
	speed switching circuit, which supplies a large
		generates, uses and can radiate radio frequency
	amount of current to operate a product. It
		energy and, if not installed and used in
	varies depending on the product.
		accordance with the instructions, may cause
	This generated sound does not affect the
		harmful interference to radio communications.
	performance and reliability of the product.
		However, there is no guarantee that interference
yyTake care not to touch the ventilation
		will not occur in a particular installation. If this
	openings. When watching the TV for a long
		equipment does cause harmful interference
	period, the ventilation openings may become
		to radio or television reception, which can be
	hot. This does not affect the performance of
		determined by turning the equipment off and
	the product or cause defects in the product.
		on, the user is encouraged to try to correct the
	yyIf the TV feels cold to the touch, there may
		interference by one or more of the following
	be a small “flicker” when it is turned on. This
		measures:
	is normal, there is nothing wrong with TV.
			- Reorient or relocate the receiving antenna.
	Some minute dot defects may be visible on
			- Increase the separation between the
	the screen, appearing as tiny red, green, or
			equipment and the receiver.
	blue spots. However, they have no adverse
			- Connect the equipment to an outlet on
	effect on the TV’s performance. Avoid
			a circuit different from that to which the
	touching the LCD screen or holding your
			receiver is connected.
	finger(s) against it for long periods of time.
			- Consult the dealer or an experienced radio/
	Doing so may produce some temporary
			TV technician for help.
	distortion effects on the screen.
		This device complies with part 15 of the FCC
	Preventing “Image burn” or “Burn-in” on your TV	Rules. Operation is subject to the following
		two conditions: (1) this device may not cause
	screen	harmful interference and (2) this device must
		accept any interference received, including
		interference that may cause undesired operation
		of the device.
		Any changes or modifications in construction of
		this device which are not expressly approved by
yyIf a fixed image displays on the TV screen for		the party responsible for compliance could void
		the user’s authority to operate the equipment.
	a long period of time, it will be imprinted and
	become a permanent disfigurement on the
			NOTE TO CABLE/TV INSTALLER
	screen. This is “image burn” or “burn-in” and
		This reminder is provided to call the CATV
	not covered by the warranty.
		system installer’s attention to Article 820-40 of
yyIf the aspect ratio of the TV is set to 4:3 for a
		the National Electric Code (U.S.A.). The code
	long period of time, image burn may occur on
		provides guidelines for proper grounding and, in
	the letterboxed area of the screen.
		particular, specifies that the cable ground shall
yyAvoid displaying a fixed image on the TV
		be connected to the grounding system of the
	screen for a long period of time (2 or more
		building, as close to the point of the cable entry
	hours for LCD, 1 or more hours for the Plasma
		as practical.
	TV) to prevent image burn.

ENGLISH