Pioneer GEX-P10HD owner manual Installation, Additional Information, Connections English

Connections		English
Connecting the units
Head unit		Blue/White
		Control signal is output through blue/white cable
(sold separately)
		when Pioneer head unit is turned on. Connect it
		to the vehicle’s auto-antenna relay control
		terminal (max. 300 mA, 12 V DC). If the vehicle is
		equipped with a glass antenna, connect it to the
		antenna booster power supply terminal.
	3 m (9 ft. 10 in.)
To IP-BUS input	IP-BUS cable
(blue)	(supplied)
		Black
		This unit
		IP-BUS cable
Antenna jack		Blue
		Multi-CD player
		(sold separately)
3 m (9 ft. 10 in.)
Antenna cable
(supplied)

Installation

Connections

Important

•Use this unit in a vehicle of a 12-volt battery and negative grounding.

•To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.

—Disconnect the negative terminal of the battery before installation.

—Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

—Place all cables away from moving parts, such as gear shift and seat rails.

—Place all cables away from hot places, such as near the heater outlet.

—Do not pass the yellow cable through a hole into the engine compartment to connect to a battery.

—Do not shorten any cables.

—Never cut the insulation of the power cable of this unit in order to share the power to other equipment. Current capacity of the cable is limited.

—Use a fuse of the rating prescribed.

•IP-BUS connectors are color-coded. Be sure to connect connectors of the same color.

•Place antenna cable as far away as possible from the other cables to prevent noise.

•Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.

English

•Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts.

•If this unit installed in the passenger compartment, anchor it securely so it does not break free while the vehicle is moving, and cause injury or an accident.

•If this unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not caught or pinched in the mechanism and cause a short-circuit.

Mounting with hook and loop fasteners

Thoroughly wipe off the surface before affixing the hook and loop fasteners.

•If the hook fasteners adhere to the car mat directly, you may install this unit without using the loop fasteners.

Mount this unit using the hook and loop fasteners.

This unit

Hook fastener

Loop fastener

Additional Information		English
Specifications
General
Rated power source	14.4 V DC
	(allowable voltage range:
	10.8 V to 15.1 V DC)
Grounding system	Negative type
Max. current consumption
.....................................	2.0 A
Dimensions (W × H × D)	121 mm × 30 mm × 79 mm
	(4-3/4 in. × 1-1/8 in. × 3-1/8 in.)
Weight	350 g (0.8 lbs)
Analog FM tuner
Frequency range	87.9 MHz to 107.9 MHz
Usable sensitivity	14 dBf (0.7 μV/75 W, mono,
	S/N: 30 dB)
Signal-to-noise ratio	61 dB (IHF-A network)
Digital FM tuner
Frequency range	87.9 MHz to 107.9 MHz
Signal-to-noise ratio	70 dB (IHF-A network)
Frequency response	30 Hz to 15 000 Hz (±3 dB)
Stereo separation	70 dB (at 1 kHz)
Analog AM tuner
Frequency range	530 kHz to 1 710 kHz (10 kHz)
Usable sensitivity	50 μV (S/N: 20 dB)
Signal-to-noise rati	58 dB (IHF-A network)

Car antenna cable (form vehicle’s antenna) Connect the car antenna cable to this unit’s antenna input. It is not necessary to connect to head unit’s antenna input.

If you use this unit with a navigation system that can receive traffic information from the built-in FM tuner, connect the car antenna cable to both this unit and the navigation system with an antenna splitter or to a separate antenna.

Fuse (2 A)	Yellow
	Connect to the constant
	12 V supply terminal.

Installing this unit

Important

•Check all connections and systems before final installation.

•Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions.

•Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle.

•Do not install this unit where:

Car mat or chassis

Digital AM tuner
Frequency range	530 kHz to 1 710 kHz (10 kHz)
Signal-to-noise ratio	70 dB (IHF-A network)
Frequency response	40 Hz to 15 000 Hz (±3 dB)
Stereo separation	70 dB (at 1 kHz)

Note

Black (chassis ground)

Connect to a clean, paint-free metal location.

—it may interfere with operation of the vehicle.

—it may cause injury to a passenger as a result of a sudden stop.

•When mounting this unit, make sure none of the leads are trapped between this unit and the surrounding metalwork or fittings.

•Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it.

Specifications and the design are subject to possible modifications without notice due to improvements.