Pioneer AVD-W6210 owner manual Cords that have the same function

Page 26

Connecting the System

Note:

•This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the bat- tery voltage.

•To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before begin- ning installation.

•Refer to the owner’s manual for details on con- necting other units, then make connections cor- rectly.

•Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

•Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, hand- brake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

•Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

•Do not shorten any leads. If you do, the protec- tion circuit may fail to work when it should.

•Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capac- ity of the lead will be exceeded, causing over- heating.

•When replacing a fuse, be sure to use only fuses of the rating prescribed on the fuse holder.

•If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be con- nected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehi- cle battery may be drained when you are away from the vehicle for several hours.

 

 

CC

 

 

 

 

 

 

 

 

 

F

A

O

 

 

 

F

O

 

 

 

 

N

 

N

O

F

 

 

 

 

O

F

 

 

 

 

 

 

 

S

 

 

 

S

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T

 

 

 

 

T

 

 

 

 

R

A

 

 

 

R

A

 

 

 

T

 

 

 

T

 

ACC position

No ACC position

CAUTION

•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect

cords that have the same function.

25

Page 25 Page 27
Image 26
Page 25 Page 27
Contents AVD-W6210 Contents We Want You Listening For a Lifetime Important Safeguards Fit part 1 into the grooves 2 of the base Fitting and Removing the DisplayTo fit the display Slide the display downward until it clicks into placeTo remove the display About This Product PrecautionWhen combined with a Pioneer navigation unit After-sales Service for Pioneer Products Product registrationTo Protect the LCD Screen of the Display Before Using This ProductTo Avoid Battery Exhaustion About the RCA Video and Audio Outputs of this UnitResetting the Microprocessor To Ensure Safe DrivingDisplay Unit Component Parts and FeaturesKey Finder Basic Operation Turn On PowerVolume Adjustment Selecting a Source Select the desired sourceChanging the Wide Screen Mode Wide Modes Available Display the setup menu Operating the Setup MenuEntering the Setup Menu Select a settingPicture Adjust Adjust the itemAdjust brightness DimmerSelect a connection mode Video SettingInput Setting AV IN2 Confirm the safety and get into reverse gear PolarityPicture Adjust Switching the image of rear displayAudio Setting Setting the Mixing of the Guidance Voice GuideUsing the Display Correctly Handling the DisplayAbout the Small Fluorescent Tube About the Liquid Crystal Display LCD ScreenKeeping the Display in Good Condition Connecting the System Cords that have the same function Names and Functions of Connection Terminals Hide-away UnitConnecting the Power Cable Connection Diagram Video input AV IN1 Input AV IN2 InputConnection Diagram 26-pin input You can connect a separately sold Pioneer Navigation unitConnecting the RCA Audio and Video Output EnglishConnecting REVERSE-GEAR Signal Input Lead Connection methodInstallation Before Affixing the Adhesive Tape Before Installing and FixingInstallation with the supplied bracket Paste the cushions onto the bot- tom of the display base Installing the Display Using the Accessory Mounting BaseInstall the display base Fix the display on the mounting baseDetermine the display installa- tion position Paste the mounting base onto the dashboardDashboard Tapping screws 3 ⋅ 12 mm Remove the display with the lock release lever Installing the Hide-away Unit Hide-away Unit InstallationSpecifications GeneralEnglish Español Deutsch Français Italiano Nederlands Table des matières Utilisation du menu de miseCher Client Importantes Mesures DE Securite Insérez la partie 1 dans les rainures 2 de la base Mise en place et retrait de l’écranMise en place de l’écran Retrait de l’écran Quelques mots concernant cet appareil PrécautionService après-vente des produits Pioneer Enregistrement du produitComment protéger l’écran à cristaux liquides Avant de vous servir de cet appareilComment éviter de décharger la batterie Pour garantir une conduite sûre Réinitialisation du microprocesseurUnité écran Tableau des commandesComposants et particularités Réglage du niveau sonore Opérations de baseMise sous tension Sélection d’une source Sélection de la source désiréeChangement du mode d’affichage sur l’écran Cinema Cinéma Full RemplirJust Juste Zoom ZoomAffichez le menu de mise en oeuvre Utilisation du menu de mise en oeuvreAccès au menu de mise en oeuvre Sélectionnez un réglageRéglage de l’image Réglez le posteDimmer Atténuateur de luminosité Réglez la luminositéRéglage de l’entrée AV IN2 Sélectionnez un mode de connexionRéglages relatifs à la vidéo Le réglage initial de Polarity est Battery Sélection de l’image affichée sur l’écran arrière MENU-ENTERRéglage audio Réglage du mélange du guide vocal GuideUtilisation convenable de l’écran Maniement de l’écranPropos du petit tube fluorescent Propos de l’écran à cristaux liquides LCDEntretien de l’écran Branchement du système Chaque câble Noms et fonctions des prises de raccordement Appareil déportéBranchement du câble d’alimentation Méthode de connexionSchéma de connexion entrée Video Schéma de connexion Entrée 26 broches Connexion à la sortie audio et vidéo Cinch RCA Connexion du conducteur REVERSE-GEAR Signal Input Violet/BlancInstallation Avant d’employer le ruban adhésif Avant l’installation et la fixationInstallation à l’aide du support fourni Collez les coussinets sur le fond de la base d’écran Installation de l’écran avec la base de montage fournieInstallez la base d’écran et la Fixez lécran sur la base de mon- tageDéterminez la position d’installation de l’écran Collez la base de montage sur la planche de bordVis taraudeuse 3 ⋅ 12 mm Détachez lécran en libérant le levier de déblocage Montage de appareil déporté Installation de appareil déportéPrécautions d’installation Caractéristiques techniques GénéralitésEnglish Français Deutsch Español Italiano Nederlands Page Page Pioneer Corporation
Related manuals
Manual 112 pages 48.57 Kb

AVD-W6210 specifications

The Pioneer AVD-W6210 is an advanced multimedia receiver designed to enhance your driving experience by providing a robust blend of entertainment and functionality. This sleek unit is particularly appealing to car enthusiasts who prioritize high-quality audio and video capabilities along with modern connectivity features.

At the heart of the AVD-W6210 is a vibrant 6.2-inch touchscreen display that offers an intuitive interface, making it easy for users to navigate through various media options and settings. The display's resolution ensures clarity whether you're watching a video or using navigation apps. The capacitive touchscreen technology enhances touch sensitivity, allowing for quick and responsive interactions.

One of the standout features of the AVD-W6210 is its extensive media compatibility. This receiver supports a variety of formats, including DVD, CD, and digital media files, making it versatile for all your entertainment needs. It also features built-in Bluetooth technology which allows for hands-free calling, as well as audio streaming from compatible devices. This wireless capability enhances safety by letting drivers keep their hands on the wheel while managing calls and music.

The AVD-W6210 is equipped with advanced audio processing technologies. Its high-performance amplifier and customizable EQ settings ensure that users can fine-tune their audio experience to suit their preferences. Additionally, the unit supports lossless audio formats and provides connectivity options for external devices, enhancing the listening experience.

Connectivity remains a key focus of the AVD-W6210, with USB and AUX input options readily available. This allows users to connect smartphones, tablets, and other devices seamlessly. Moreover, the receiver is compatible with both Android Auto and Apple CarPlay, making it easier than ever to harness your smartphone’s functionalities directly through the unit. This feature supports navigation and voice control, enabling users to access their favorite apps hands-free.

For those desiring enhanced sound quality, the AVD-W6210 offers compatibility with various external amplifiers and speakers, providing a route for users to elevate their audio system further. It also features multiple preamp outputs for easy installation of aftermarket amplifiers.

In conclusion, the Pioneer AVD-W6210 presents an exceptional choice for those looking to enrich their in-car entertainment experience with a blend of high-quality audio, intuitive controls, and modern connectivity technologies. Its thoughtful design and robust features make it a reliable companion for any journey.
Top Page Image Contents