Planar EP4650, EP5550 manual Safety Information, Safety Precautions

Page 8

Safety Information

Safety Information

Before using the EP4650/EP5550, please read this manual thoroughly to help protect against damage to property, and to ensure personnel safety.

Be sure to observe the following instructions.

For your safety, be sure to observe ALL the warnings detailed in this manual.

For installation or adjustment, please follow this manual’s instructions, and refer all servicing to qualified service personnel.

Safety Precautions

If water is spilled or objects are dropped inside the ep46L/ep55L, remove the power plug from the outlet immediately. Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

If the EP4650/EP5550 is dropped or the chassis is damaged, remove the power plug from the outlet immediately. Failure to do so may result in fire or electrical shock. Contact your dealer for inspection.

WARNING! Wall mounts must be secure.

If the display is hung on a wall, the wall must be strong enough to hold it. Simply mounting it to wallboard or wall paneling won’t be adequate or safe.

Caution: The screen could be damaged by heavy pressure.

Slight pressure on the LCD will cause distortion of the image. Heavier pressure will cause permanent damage. Displays should be mounted where viewers cannot touch the screen or insert small objects in the openings that will create hazards by contacting bare conductive parts.

Caution: The front polarizer is soft and subject to scratches from sharp objects.

The polarizer is a thin sheet of film laminated to the outside layer of glass on the LCD screen. Take care when handling items near the screen.

If the power cord or plug is damaged or becomes hot, turn off the main power switch of the display. Make sure the power plug has cooled down and remove the power plug from the outlet. If the EP4650/EP5550 is still used in this condition, it may cause a fire or an electrical shock. Contact your dealer for a replacement.

2

EP4650/EP5550 User Manual

Image 8
Contents EP4650/EP5550 User Guide Disclaimer Warranty and Service Plans RoHS Compliance StatementTrademark Credits Table of Contents Navigating Through the Menus Downloading Additional Documentation and Firmware Table of Contents Introduction Safety Information Safety PrecautionsImportant Safety Instructions Burn-In Versus Temporary Image Retention What is Temporary Image Retention?Recommended Usage European Union Disposal Information Cooling Requirements Vesa Mounts, General DescriptionNormal Usage Guidelines Cleaning the EP4650/EP5550 Package Contents Remove the accessory bag and packing list Description QuantityContents of the Accessory Kit Dimensions EP4560 FrontEP4560 Rear EP4560 Side Standard Inputs Optional HD-SDI/VW Inputs EP5550 FrontEP5550 Rear EP5550 Side Installing an EP4650/EP5550 Plan Your InstallationBefore You Begin Tools/Equipment ListPower Input Prepare Your Installation LocationSignal Source Input Name ConnectorOperating EP4560/EP5550 OSD KeypadOSD Keypad Buttons Key DescriptionsRemote Control Receiver LED Indicators Using the Display in Portrait ModeLED On ConditionUsing the Remote Control Num Function Customer Hex Code Description InfoLocking/Unlocking the OSD Menus ScalingChanging the Remote Control Battery Turning the EP4650/EP5550 OnAdjusting the Volume Turning the EP4650/EP5550 OffSelecting the Input Source PIP Mode PIP MainSwap Main PIP Screen Table HD-SDIMenu OSD Menu FunctionsSecondary  , DVI Advanced Multi-Display Matrix Y Image Settings Display Settings OSD MenusAudio Settings Basic Settings RTC Submenus Advanced Settings Network Settings Navigating Through the Menus Multi-Display Control System StatusImage Settings Menu Scheme Brightness Contrast Sharpness Saturation HueRange 0~100 Display Settings Menu PIP Mode PIP PositionAspect Ratio Zoom Auto Scan Select Source Range 0~10 Range On, OffAudio Settings Menu Volume Bass TrebleAspect Ratio Side by Side Scale Auto Scan Select Source Options On, OffOSD Transparent OSD Location OSD Zoom Basic Settings MenuBalance Hdmi Audio Input DP Audio Input Internal Speakers Options On, Off Options 5~120Real Time Timer Mode Basic Menu/RTC Real Time Clock MenuRTC Timer Mode User Timer Mode User modeRTC Timer Mode Work Days Timer Mode Work Days modeRTC Timer Mode All Days Timer Mode All Days modeAdvanced Settings Menu Auto Adjustment Image Position Phase Clocks VGA ADC SettingsOptions Flesh ToneOptions On Advanced Settings Ethernet Setup Submenu Options No, YesUser ADC Calibration Advanced Settings Multi-Display Control Submenu Monitor ID Video Wall DVI Indemnity Power On Delay Frame Options Yes, NoSystem Status Menu Matrix Matrix Y Division Division YDefault Settings DefaultSupported Operating Systems InstallationLAN Control Installation Installation Installation Configuring Vcom Create a Remove an Virtual Search By IP Function DescriptionsSearch Configure IP Address WebAdding a Virtual COM Port Removing a COM Port Setting Up Email Alerts LoginLogin System IP Configuration AdministratorAuthentication Configuration Load Default Setting Firmware Update and Boot Loader Upgrade TCP Mode, UDP Mode and Uart SmtpReset Device Component Video Display Port Signal CompatibilityTiming FH KHz FV Hz Timing KHzfH HzfV Component Video-SSpecifications SpecificationKeys , SOURCE, , , , , MENU/EXIT Troubleshooting Issue Check for the followingDownloading Additional Documentation and Firmware Accessing Planar’s Technical Support WebsiteDocument Name Contents Enter your login and password information Downloading Utility SoftwareIndex TIR see temporary image retention