Unpacking, Installation | Marshall electronic V-R842DP-DVI manual

Specifications

Installation and Initial Setup

■ PANEL

Screen Size	8.4” Diagonal
Display Area (h x v)	170.469 x 127.872 mm
Aspect Ratio	4:3 Native (4:3/16:9 Modes)
Pixels	1024 x RGB x 768
Color Depth	24-bit (16,777,216 Colors)
Viewing Angle (h x v)	170° x 170°
Brightness	400 cd/m2
Contrast Ratio	400:1
Dot Pitch (h x v)	0.0555 x 0.1665 mm
Pixel Pitch (h x v)	0.1665 x 0.1665 mm

■VIDEO INPUT/OUTPUT

VGA Input

Supports RGBHV, RsGsBs, RGsB, RGB CS,

DVI Input

Supports Digital Signals Only (DVI-D) HDMI, HDCP Supported

■CONNECTORS

Video Input
VGA	1 x HD-15 Female
DVI	1 x DVI-I 29-Pin Female

Power Input

2-Pin Twist Lock Connector

Tally Interface

HD-15 Female

■TALLY

3 LEDs (Green, Red, Yellow). Activation requires contact closure of pin to ground on the HD-15 connector:


	Pin No.					Signal
	1					M1 Green
	2					M1 Red
	3					M1 Yellow
	4					Ground
	5					Ground
	6					N/C
	7					N/C
	8					N/C
	9					N/C
	10					N/C
	11					M2 Green
	12					M2 Red
	13					M2 Yellow
	14					Ground
	15					Ground

■ ELECTRICAL

Power Consumption	3.5A @ 12VDC (42 W)
Voltage Requirement	12 VDC
V-PS12-5V-1 Power Supply:
Input	100V-240V, 1.5A, 50-60Hz
Output	12VDC, 5A, 60W Max

■MECHANICAL

Dimensions (w x h x d): 18.92” x 7.00” x 2.02”

Weight (Monitor Only):	6.70 lbs
Operating Temperature	32°F to 120°F (0°C to 50°C)
Storage Temperature	-4°F to120°F (-20°C to 50°C)
Compliance	₠, FCC-Class A, ANSI-63.4
	(Certificates on file)
RoHs	Do not dispose. Return to
	Manufacturer or Authorized
	Recycle Facility.

■Unpacking

Carefully unpack the V-R842DP-DVI monitor and verify that the following items are included:

•V-R842DP-DVI Monitor

•V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector

•Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-0606.

■Installation

The V-R842DP-DVI can be mounted in any standard EIA 19” equipment rack. Adequate ventilation is required when installed to prevent possible damage to the monitor’s internal components.

■Connections and Power-On

Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a variety of sources. The monitor will draw approximately 3.5 Amps at 12 Volts in operation.

Connect the required cables for video signal input and output.

Each screen may be turned on by pressing the power button located on the front panel. Select a video input by pressing the corresponding input select button.