Axis Communications P7216 manual Connectors, For specifications, see

Page 9

AXIS P7216 Video Encoder

Connectors

For specifications, see page 10.

BNC connector - Each video input is terminated using a coax/BNC connector. Connect a 75 Ohm coaxial video cable; the recommended maximum length is 800 feet (250 meters).

Note

75 Ohm video termination can be enabled/disabled for the video input via the product's web page at Video & Audio > Video Input > Video termination. This termination is enabled on factory default. In cases where the product is to be connected in parallel with other equipment, for optimum video quality, it is recommended that termination be enabled for only the last device in the video signal chain.

Network connector - RJ45 Ethernet connector.

SFP connector - The unit can only use one Network interface, either an SFP module or RJ45 connector. SFP module has higher priority than the RJ45 connector.

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out.

SD card slot - A standard or high-capacity microSD card (not included) can be used for local recording with removable storage.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Control button - The control button is used for:

Resetting the product to factory default settings. See page 14.

Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS Service. For more information about these services, see the User Manual.

9

Image 9
Contents Installation Guide Liability Legal ConsiderationsIntellectual Property Rights Equipment ModificationsKorea Page Axis P7216 Video Encoder Safety Information Hazard LevelsOther Message Levels Axis P7216 Video Encoder Safety Instructions BatteryTransportation Installation Steps Axis P7216 Video Encoder Installation GuidePackage Contents Hardware OverviewLED Indicators Axis P7216 Video EncoderColor Indication For specifications, see ConnectorsSpecifications Power ConsumptionOperating Conditions Function Pin Specifications Terminal connectorAudio connector Power connectorMount the video encoder Install the HardwareAuxiliary Connector Access the Product Reset to Factory Default SettingsConnect the cables Further Information Warranty Information Installation Guide

P7216 specifications

Axis Communications P7216 is a powerful video encoder designed to deliver high-quality video streaming from analog surveillance cameras to IP networks. This device plays a crucial role in modernizing older CCTV systems by converting their output into a digital format compatible with IP technology. The P7216 is particularly well-suited for organizations looking to enhance their surveillance capabilities without having to fully replace their existing analog cameras.

One of the standout features of the P7216 is its ability to transmit up to 16 analog video channels simultaneously. This high channel capacity makes it ideal for large-scale installations where multiple cameras are in use. In addition to video, the device also supports audio streaming, allowing for two-way audio communication, which adds an extra layer of functionality to the surveillance system.

The P7216 is equipped with advanced H.264 video compression technology, which optimizes video quality while significantly reducing bandwidth and storage requirements. This efficient compression ensures that even high-resolution analog cameras can send real-time video streams without overwhelming network resources. Moreover, it supports multiple streams, enabling different resolutions or formats to be sent to various devices based on specific needs.

With a robust web-based management interface, users can easily configure and manage the P7216 remotely. This feature simplifies the process of setting up video encoders across multiple sites and helps in monitoring the entire surveillance system effectively. Additionally, the device is compatible with a wide range of video management software (VMS), allowing users to integrate it seamlessly into existing security infrastructure.

The P7216 also boasts advanced security features, including HTTPS encryption, password protection, and secure network protocols, which help safeguard sensitive footage against unauthorized access. Its rugged design is specifically built for durability, making it suitable for a variety of environmental conditions.

Overall, the Axis Communications P7216 combines versatility, reliability, and advanced technology, making it a valuable addition to any surveillance setup. By leveraging its capabilities, organizations can maximize the utility of their analog systems while moving towards IP-based surveillance solutions, ensuring enhanced security and operational efficiency.