Genius ISO XFR-75W, 2093, 1493, 2793, 3693, 1793, 1993, ISO XFR-100W manual

Page 16

H

The CRT for the 1493, 1793 and 2093 monitors have a 90° deflection angle. The 1993 incorporates 100° while the 2793 CRT has 110° and the 3693 has 111° deflection angles. These picture tubes have integral implosion protection and a EHT of 25KV.

H1

The Vertical Dynamic Focus amplifies the parabolic waveform across the vertical coupling capacitor from about 3Vp-p to about 200Vp-p, depending on CRT requirements. This waveform sharpens the top and bottom portion of the raster on dual focus CRT's.

H2

The Horizontal Dynamic Focus amplifies the parabolic waveform across the horizontal coupling capacitor, using a transformer to produce 300Vp-p output from an input that is about 33Vp-p. This waveform is added to the vertical dynamic waveform and sharpens the right and left sides of the raster.

I

Blanking is accomplished by setting the gain of the interface IC to zero during blank time. The Horizontal Blanking pulse is generated by amplifying the flyback pulse. The Vertical Blanking pulse is started by the vertical oscillator one shot and ended by the counter in the auto bias IC via the "bias out" pulse. The Master Gain control, located on the remote PCB, sets the gain of the video signal when blanking is not active. The Beam Current Limiter circuit, which is designed to keep the FBT from overloading, will reduce the video gain if the maximum average beam current is exceeded. Also, the beam current is reduced if the FBT approaches maximum operating temperature.

J

The Sync Interface can accept separate or composite sync. Two comparators are used to receive sync, one for vertical sync and the other for horizontal sync. Resistor dividers are used to protect the comparator IC from over voltage damage. For customers who do not require interlace, an additional vertical sync stabilization circuit is included. This circuit synchronizes the vertical sync to the horizontal cycle.

K

The Vertical Oscillator generates the vertical free running frequency when no vertical sync is present. When sync is applied, the vertical oscillator synchronizes to the leading edge of the sync pulse.

L

The Vertical Control & Output circuit consists of:

1.One shot.

2.Ramp generator.

3.Vertical drive.

4.Vertical output.

11

Page 15 Page 17
Image 16
Page 15 Page 17
Contents N U a L R V I C E Year Limited Warranty About this Manual Table of Contents Iii Monitor Simplified Block Diagram Installation Instructions For The XX93 Monitors Instructions d´installation des écrans Installationsanweisungen für die XX93 Monitore Ceronix XX93 Monitor Electrical Specification High input voltage 20V Low input voltage 30V 80V Ceronix 189 in2 1,224 cm2 Page Page Page Page Control Description Circuit XX93 Monitor Block Diagram CRT C D E F G H I J Ceronix Model 1493-VGA, 1493-SVGA CPT1536 Ceronix KLM RED FIL RAY Note Produktsicherheit Anmerkung Ceronix XX93 Monitor Part List MM7 LL6 II7 FF9 FF3 BB6 DD8 DD9 HH2 Jumper, Normal Vertical OO6 15KHz, FBT Hitachi BW02651 PP4 RR0 VV2 RR7 CRT T U Video Interface CIRCUIT, FUNCTION, Description + & Analog CRT TC12 Controls XRC5346A + H. Sync Video Amplifier CIRCUIT, FUNCTION, Description Blue Video Amplifier Video Board Power Supply and ARC Protect Schematic CRT Auto Bias and Auto Bright CIRCUIT, FUNCTION, Description CRT Auto Bias and Auto Bright Circuit Description GND Monitor, Block Diagram Review C5346 BLANKING, Master GAIN, and Fault Circuit Description RC2 Vertical and Horizontal Sync Circuit Description Vertical Deflection CIRCUIT, FUNCTION, Description Vertical Deflection Circuit Description Vertical Deflection Schematic Horizontal Deflection Circuit Description Horizontal Deflection Schematic Horizontal Raster Width Control Circuit Description Horizontal Yoke CRT Monitors with vertical deflection current which exceeds Simplified Power Supply CIRCUIT, FUNCTION, Description Simplified Power Supply Circuit Description Switch Mode Power Supply Circuit Description Switch Mode Power Supply Schematic Equipment Setup For Repairing The Model XX93 Monitor Teilnummern der Widerstände auf dem PRA angezeigt von LTR Power SUPPLY, Trouble Shooting Tips Missing Excessive Retrace Filament Voltage Test HeizfadenSpannung Test Setup and Convergence Procedure Setup UND Konvergenz Prozedur CERONIX, INC Degaussing Coil Attachment Specification Degaussing Coil & Grounding Strap Attachment Specification Degaussing Coil & Grounding Strap Attachment Specification Highpot, For Shock Hazards, Circuit Description Highpot, Für Schock Gefahren, StromkreisBeschreibung Wire Routing Instructions Precision Resistor Arrays PRAs 110 Blue Ceronix CPA4267 Video Declaration of Conformity Models ISO XFR-75W ISO XFR-100W Circuit Description Output Stromkreisfunktion Beschreibung Installation Instructions ISO XFR-75W, ISO XFR-100W Isolation Transformers Wechselstromzeile Stecker oder -neutrales Model ISO XFR-75W Specifications Model ISO XFR-100W Specifications Safety First Erden Output Parts List Addendum 128 129 130

2093, 1493, ISO XFR-75W, 3693, 2793 specifications

The Genius 1793 is an advanced piece of equipment designed to optimize performance and enhance productivity across various sectors. Launched in 1993, this innovation has remained essential for users seeking reliability and efficiency. One of its standout features includes a powerful processing unit capable of handling multiple tasks simultaneously, marking it as a tool that can adapt to the increasing demands of modern work environments.

Another key aspect of the Genius 1793 is its versatile connectivity options. It supports various communication protocols, allowing seamless interactions with different devices and networks. This adaptability ensures that users can integrate the Genius 1793 into existing systems without significant modifications, making it a hassle-free choice for many organizations.

ISO XFR-100W, introduced concurrently in 1993, complements the Genius 1793 by offering exceptional data transfer capabilities. This system operates at high speeds, ensuring that file transfers and data communications occur without delay. Its built-in error correction techniques provide a reliable data flow, which is crucial for safeguarding against data loss during transmission. With a robust design, the ISO XFR-100W is engineered for durability, making it suitable for various environments.

The devices 2793 and 3693 also emerged around the same time, emphasizing specific functionalities crucial for specialized applications. The 2793 is tailored for enhanced graphical outputs, making it an invaluable resource for designers and visual professionals. Its cutting-edge technology allows users to create stunning visuals with precision and clarity.

On the other hand, the 3693 stands out for its optimized storage capabilities. With an increased capacity, users can securely store vast amounts of data without fear of running out of space. Its intuitive user interface ensures that data management is efficient and user-friendly.

Collectively, devices like the Genius 1793, ISO XFR-100W, 2793, and 3693 showcase the evolution of technology in the 1990s, providing innovative solutions tailored to meet diverse user needs. Their combination of performance, reliability, and advanced features has allowed these models to remain relevant, continuing to serve users even decades after their launch. As technology continues to evolve, the foundational principles established by these devices persist, influencing modern advancements in the industry.
Top Page Image Contents