Blaupunkt RDM 169 Adjusting DNC sensitivity, Switching DNC on/off, Safety information

Page 36

DNC – Dynamic Noise Covering

DNC is used when the vehicle is in motion to boost the car audio system’s volume to a level which is considered pleasant in the stationary vehicle.

The volume is boosted at different levels for the different frequency ranges, depending on the amount of noise which develops in the vehicle.

To start taking the reading:

To alter the sensitivity

• Press DSA.

• press DNC briefly, the value selected

 

will appear in the top line of the dis-

 

play.

 

Press / to alter the value as desired.

 

Press ENT to store this new setting and

 

press EXIT to quit the DSA menu.

ENGLISH DEUTSCH

This keeps the volume and the sound of the audio equipment at acceptable levels while the background noise changes. Short-term noise, such as the noise made when you drive over a set of railway tracks, will not affect the volume.

Adjusting DNC

If DNC is to operate correctly for your vehi- cle, it is necessary to take a reading with the microphone. Take the DNC reading af- ter you take the hi-fi self-adjustment read- ings. Use the enclosed tape to secure the microphone somewhere near the dash- board, but not in the foot area, near any- thing that reverberates or near the heating/ cooling fans.

The microphone head must be facing to- wards the passengers. The reading should be taken in a quiet area with the engine switched off.

•Press DNC for approx. 1 sec. until “DNC Adj” appears in the top line of the display.

The DNC reading will now begin and be completed fully automatically.

As soon as “DNC 3” appears in the top line of the display, the reading has been com- pleted. The value will be set to average DNC sensitivity automatically.

Adjusting DNC sensitivity

The volume boost can be set to five differ- ent levels:

Select DNC 1 if you have a loud engine and usually listen to music with a lot of bass, select DNC 5 if your vehicle runs very qui- etly and you usually select classical music. After you have taken a reading, the value will automatically be set to DNC 3.

Switching DNC on/off

•To switch DNC off, press <<.

”DNC off” will appear in the top line of the display.

•To switch DNC on, press >>.

Safety information

If the microphone is placed in the wrong position, the DNC reading will be incorrect.

As a result, the volume might be boosted too much while you are driving (could star- tle the driver).

Please make sure to position the micro- phone correctly.

FRANÇAIS ITALIANO NEDERLANDS SVENSKA ESPAÑOL PORTUGUÊS

81

Page 35 Page 37
Image 36
Page 35 Page 37
Contents San Francisco RDM Page Contents Contents Quick Reference Quick Reference Next FMNext AM MW, LW Menu level Adjusting the radio functions Switch toPRE ExitPTY REG RegionalRT Radio text MonoCLR NameAUD DISDisplay DOT field= CDC ? TU tunerVisual theft protection KeyCard theft protection systemInserting the KeyCard EjectRC 08 remote control unit Radio operation Station seek tuning upSRC Source Select track up Press briefly CUE fast forward audibleImportant notes KeyCard theft protection system Operating the unit for the first timeRemoving the KeyCard Training a second KeyCard / Replacing a KeyCardKeyCard theft protection system First-time installation First-time installation Reset to default settingsSwitching the ignition connec- tion on/off Closing the Install menuSelecting the operating Optimising the viewing Mode Angle Switching between the menu levels Radio operation with RDS Radio Data SystemAF Alternative frequency Station tuning Radio operation with RDS Radio Data SystemREG regional program Selecting a wavebandManual tuning with Scrolling through the broadcast- ing networks FM onlyChanging the memory bank FM Storing stationsScanning stored stations with Preset Scan Recalling stored stationsAutomatically storing Strongest stations with Travel StoreSwitching from stereo to mono Selecting the seek tuning sensi Automatic bandwidth adjustChanging the scan time Scan TivityProgram type NewsSelecting and storing PTY program types Selecting stored program typesPTY seek tuning Radio textStoring program types Activating radio textSwitching radio text off Switching the warning beep offTraffic information station reception with RDS-EON Traffic announcement priorityAutomatic seek tuning start Switching on CD operationCD operation / CD changer operation Removing a CDSwitching on CD changer operation Selecting the display modeCD operation / CD changer operation Selecting tracksSwitching TPM playback on/off Repeating tracks/CDsStoring tracks with TPM Deleting the TPMEntering CD names Deleting CD names/TPM at the same timeClock display when the audio system is switched off Clock TimeDisplaying the clock Automatically Selecting a 12 or 24-hour mode Activating the equalizer settings Synchronisation An overview of the equalizer functionsSwitching the equalizer on/off Self-adjusting equalizerHi-fi self-adjustment Starting the hi-fi self-adjustmentManual equalizer adjustment Activating an equalizer settingAltering the setting manually Adjusting DNC Adjusting DNC sensitivitySwitching DNC on/off Safety informationDSC programming TUN TunerDSC programming VAR VariousRead Scan ScantimeTOM CLK Clock SETSync ModeOverview of the DSC default settings CDC ChangerSpecifications Glossary Technical Terminology AmplifierTuner CD playerPreset Scan Glossary Technical TerminologyREG Softkey Software keyIndex RDS-EONTPM Blaupunkt-Werke GmbH
Related manuals
Manual 30 pages 14.63 Kb Manual 30 pages 11.18 Kb Manual 48 pages 63.2 Kb
Top Page Image Contents