JVC KD-LX111, KD-LX333 manual To change the AM/FM channel intervals, Area

Page 21

To select the subwoofer cutoff frequency

WooferFreq (only for KD-LX333)

When a subwoofer is connected to this unit, select an appropriate cutoff frequency level for your subwoofer. When shipped from the factory, the subwoofer cutoff frequency is set to “FREQ MID.”

FREQ LOW: Frequencies higher than 50 Hz are cut off to the subwoofer.

FREQ MID: Frequencies higher than 80 Hz are cut off to the subwoofer.

FREQ HIGH: Frequencies higher than 120 Hz are cut off to the subwoofer.

To change the AM/FM channel intervals

AREA

When this unit is shipped from the factory, the channel intervals are set to 10 kHz for AM and 200 kHz for FM (AREA US settings).

You will have to change the channel intervals when using this unit in an area other than North America and South America.

AREA EU:

Select this when using this unit

 

 

in an area other than North and

 

 

South America.

 

 

(9 kHz for AM and 50 kHz (for

 

 

manual tuning) / 100 kHz (for

 

 

searching) for FM)

AREA US:

Select this when using this unit

 

 

in North or South America.

 

 

(10 kHz for AM and 200 kHz for

 

 

FM)

Note:

If the channel intervals settings are changed, the following will occur.

The names assigned to the stations will be erased from memory. To reassign the names, see “Assigning names to the sources” on pages

23 and 24.

To adjust the line input level — LINE ADJ

(only for KD-LX333)

Adjust the line input level properly when an external component is connected to the LINE INPUT plugs. When shipped from the factory, the line input level is set at level “00.”

If the input level of the connected component is not high enough, increase the input level properly. Without adjusting the line input level, you may be surprised at a loud sound when you change from the external component to another source.

To select the external component to use

––EXT INPUT (only for KD-LX111)

You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied).

To use the external component as the playback source through this unit, you need to select which component – CD changer or external component

to use. When shipped from the factory, CD changer is selected as the external component.

LINE INPUT: To use the external component other than CD changer.

CD CHANGER:To use the CD changer.

Note:

For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).

To make the front panel look flat (hiding the control panel) — FLAT PANEL

When operating the receiver using the remote control, you can hide the control panel to make the front panel look flat. When shipped from the factory, “FLAT OFF” is selected.

• FLAT ON:

The control panel will not come

 

out when you turn on the unit.

 

To use the control panel, press

 

4

so that the control

 

panel comes out. If no

 

operation is done for about 10

 

seconds, it automatically goes

 

back into the receiver.

• FLAT OFF:

You can use the control panel

 

normally.

Note:

When “FLAT ON” is selected, you can eject a CD by

holding 4 .

ENGLISH

21

Image 21
Contents For customer Use KD-LX333/KD-LX111How to reset your unit PrecautionsInformation For U.S.A Contents How to use the number buttons Location of the ButtonsControl panel Remote controller Installing the battery Preparing the remoteController To drop the volume in a moment Turning on the powerTo turn off the power Basic OperationsCanceling the demonstration Setting the clockSet the hour Set the minuteListening to the radio Radio Basic OperationsSearching a station automatically Auto search Searching a station manually Manual searchStoring stations in memory FM station automatic preset SSMTune in to a station you want while M is flashing Select the FM band FM1 3 you want to store FM stations intoTuning in to a preset station Manual presetSelect the band in this example, FM1 Playing a CD CD OperationsTo stop play and eject the CD Open the loading slotSelecting CD playback modes Playing a CD Text Prohibiting CD ejectionTo play back only intros Intro Scan Adjusting the sound Sound AdjustmentsWhat is BBE II? BALFor Preset values Select the sound mode you wantActivate custom equalizer CEQ User Rock Classic Jazz HIP HOP PopsSelect the items you want to adjust Storing your own sound adjustmentsRepeat steps 4 and 5 to adjust the other items Repeat the same procedure to store other sound modesBasic Procedure Select the PSM item you want to adjust. SeeOther Main Functions Press SEL S to finish the setting Preferred Setting Mode PSM itemsTo adjust the display contrast level To select the dimmer mode DimmerTo select the scroll mode Scroll To set the clock display Clock DispTo adjust the line input level Line ADJ Only for KD-LX333 To change the AM/FM channel intervalsArea Controlling the volume automatically Audio Cruise To adjust the volume increase rateCruise 1 Cruise Cruise OFF Sources Assigning names toIf Audio Cruise does not function correctly Select a source you want to assign a name toTo erase the input characters Available charactersSelect the character set you want while is flashing Playing CDs CD Changer OperationsSelect the CD automatic changer CD-CH To go to the next tracks or the previous tracksCanceled To show the CD Text informationTo go to a particular disc directly Mode Indication Plays Beginnings Seconds IndicatorREPEAT1 REPEAT2 INTRO1 INTRO2Playing an external component Using a subwooferSelect the external component Operate the external componentTroubleshooting Symptoms Causes RemediesLonger screws than specified Handling CDs MaintenanceSpecifications FM TunerAM Tuner Call