Alpine TDM-7584R, TDM-7586RB, TDM-7582R owner manual Installation and Connections, Precautions

Page 22

Installation and Connections

Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.

WARNING

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

CAUTION

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

Precautions

•Be sure to disconnect the negative cable from the (–) pole of the battery before connecting your TDM-7586RB/ TDM-7584R/TDM-7582R to avoid short circuits.

•Use the correct ampere rating when replacing fuses. Failure to do so may result in fire or electric shock.

•Be sure to connect the leads correctly according to the diagram. Otherwise malfunctioning of the unit and/or damage to the vehicle may occur.

•Be sure to connect the speaker (–) leads to the speaker

(–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

•Use only vehicles with a 12 volt negative (–) ground. Check with your dealer if you are not sure. Failure to do so may result in fire or electric shock.

•You must be very careful when connecting wires to the vehicle's electrical system. Be sure you do not use leads of factory installed components (like an on-board computer). When connecting TDM-7586RB/TDM- 7584R/TDM-7582R to the fuse box, make sure the fuse for the intended circuit of the TDM-7586RB/TDM- 7584R/TDM-7582R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

•The TDM-7586RB/TDM-7584R/TDM-7582R uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connections. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

20-EN

Page 21 Page 23
Image 22
Page 21 Page 23
Contents TDM-7586RB Alpine CD Changers Give You More Contents Precautions Handling the Detachable Front Panel Detaching the Front Panel Connectable to Remote Control Interface BoxBasic Operation Initial System Start-UpTurning Loudness On/Off Turning Power On and OffAdjusting Source Signal Levels FAD ← BAL ←Manual Storing of Station Presets Manual TuningAutomatic Seek Tuning Radio OperationAutomatic Memory of Station Presets Tuning to Preset StationsWhen the RDS station signal received has become weak Setting RDS Reception Mode and Receiving RDS StationsRecalling Preset RDS Stations RDS OperationReceiving Traffic Information PTY Programme Type TuningWhen traffic information stations cannot be received Receiving Traffic Information While Playing Tape or RadioPriority News Receiving RDS Regional Local StationsRepeat Play Cassette Player OperationInserting/Ejecting Cassette Normal Play and PauseManual Reverse Fast Forward and RewindScanning Programmes Programme Sensor P.SMusic Sensor M.S. Skip CD Changer OperationFast Forward and Backward Repeat Play on Single Track or Entire Disc X. Random PlayTo Display CD Titles TDM-7586RB/TDM-7584R only Remote Control Operation Battery Replacement Information Case of DifficultySpecifications Remote Control TDM-7586RB/TDM-7584R onlyInstallation and Connections PrecautionsInstallation RemovalConnections SpeakersRear Output RCA Connectors To prevent external noise from entering the audio system

TDM-7582R, TDM-7584R, TDM-7586RB specifications

The Alpine TDM-7586RB, TDM-7584R, and TDM-7582R are high-performance multimedia receivers that stand out in the automotive audio market. These models are designed to enhance the driving experience by delivering superior sound quality, versatile connectivity, and user-friendly interfaces.

One of the prominent features of these receivers is their advanced audio processing capabilities. The TDM-7586RB, for instance, incorporates a high-resolution DAC (Digital-to-Analog Converter) that ensures precise audio reproduction, delivering clear highs and deep bass. The TDM-7584R and TDM-7582R also inherit this feature, providing a premium audio experience no matter the genre of music. Additionally, built-in sound adjustment tools allow users to tailor the sound output to their preference, making it possible to adjust the equalizer settings according to individual taste.

Connectivity is a key highlight of these Alpine models. Each receiver supports Bluetooth technology for wireless audio streaming from smartphones and other devices. The inclusion of USB ports allows for direct playback from flash drives, while auxiliary inputs offer further versatility for connecting various external devices. Compatibility with both Android and iOS systems ensures that all users can easily integrate their smartphones for hands-free calling and navigation.

The TDM-7586RB features a larger, high-resolution touchscreen display that facilitates easy navigation through menus and settings, making it user-friendly. The TDM-7584R and TDM-7582R, while slightly smaller, maintain high visibility and responsiveness, ensuring that drivers can operate the receiver without distraction.

The receivers are also equipped with advanced radio functionality, providing access to FM and AM stations, as well as support for digital radio services in certain regions. The built-in tuner enhances the listening experience by delivering clear reception even in challenging environments.

In terms of build quality, the TDM series is designed to withstand the rigors of automotive environments. They feature durable materials and components that ensure long-lasting performance and reliability.

Overall, the Alpine TDM-7586RB, TDM-7584R, and TDM-7582R offer a blend of advanced audio technology, connectivity options, and user-oriented features, making them ideal choices for those looking to elevate their in-car entertainment experience.
Top Page Image Contents