JVC KD-R710 user service Setting the clock Basic operations, Preparations

KD-R710

CD RECEIVER : INSTRUCTIONS

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

1209DTSMDTJEIN
EN	GET0647-001B
© 2009 Victor Company of Japan, Limited	[J]

Canceling the display demonstration

1	Turn on the power.	4	Select <DEMO OFF>.
2	[Hold]	5
3	(Initial setting)
		6	Finish the procedure.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

IMPORTANT FOR LASER PRODUCTS

1.CLASS 1 LASER PRODUCT

2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3.CAUTION: (For U.S.A.)	Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada)	Visible and/or invisible class 1M laser radiation when open. Do not view directly
	with optical instruments.
4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
		[European Union
		only]
Warning:		For safety...
If you need to operate the unit while driving, be sure		• Do not raise the volume level too much, as this will
to look around carefully or you may be involved in a		block outside sounds, making driving dangerous.
traffic accident.		• Stop the car before performing any complicated
Caution on volume setting:		operations.
		Temperature inside the car...
Digital devices (CD/USB) produce very little noise
compared with other sources. Lower the volume		If you have parked the car for a long time in hot or
before playing these digital sources to avoid		cold weather, wait until the temperature in the car
damaging the speakers by the sudden increase of		becomes normal before operating the unit.
the output level.

Setting the clock			Basic operations
			Ejects the disc	Loading slot Control dial	Display window	Auxiliary input jack
1	Turn on the power.	5
			Adjust the hour.
2	[Hold]	6	Adjust the minute.
	(Initial setting)
3
	Select <CLOCK>.

Detaches the panel

7 Finish the procedure.

4 Select <CLOCK SET>.

Returns to the previous menu
Remote sensor	USB (Universal Serial
• DO NOT expose to bright sunlight.
	Bus) input terminal

When you press or hold the following button(s)...

Preparations

How to attach/detach the control panel

How to reset your unit

Reset the unit after installation is completed.

• Your preset adjustments will also be erased (except the registered Bluetooth device, see page 3).

How to forcibly eject a disc

[Hold]

•You can forcibly eject the loaded disc even if the disc is locked. To lock/unlock the disc, see page 2.

•Be careful not to drop the disc when it ejects.

•If this does not work, reset your unit.

Preparing the remote controller (RM-RK50)

When you use the remote controller for the first time, pull out the insulation sheet.

Insulation sheet

If the effectiveness of the remote controller decreases, replace the battery.

Replacing the lithium coin battery

CR2025

For USA-California Only:

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Caution:

•Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

•Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

Warning (about battery handling)

To prevent accidents and damage:

•Do not install any battery other than CR2025 or its equivalent.

•Store out of reach of children.

•Do not recharge, short, or dismantle.

•Do not dispose of in fire.

•Do not carry around with other metallic materials.

•Wrap the battery with tape and insulate when throwing away or saving it.

Main unit	Remote	General operations
	controller

	Turns on.
	• When the power is on, pressing		/I/ATT on the remote controller also mutes the
	sound or pauses. Press	/I/ATT again to cancel muting or resume playback.
	Turns off if pressed and held.
	Selects the available sources (if the power is turned on).
	• If the source is ready, playback also starts.
	Adjusts the volume level.
	• Selects item if turn the control dial on the main unit.
	• Mutes the sound while listening to a source. If the source is “CD,” “USB FRONT/
	USB REAR,” or “IPOD-FRONT/IPOD-REAR,” playback pauses. Press the control dial
—	again to cancel muting or resume playback.
	• Enters playback mode menu directly if pressed and held.
	• Confirms selection.

		Selects the sound mode.
		• Enters tone level adjustment directly (see page 4) if pressed and held EQ BASS-TRE
		on the main unit.
	—	• Enters “Call Menu” screen or answers incoming call when the unit rings.
		• Ends a call if pressed and held.
	—	Power off : Checks the current clock time.
		Power on : Changes the display information.
For Bluetooth operations, see pages 2 to 4.

• Microsoft and Windows Media are either registered	• Apple is not responsible for the operation of this
trademarks or trademarks of Microsoft Corporation	device or its compliance with safety and regulatory
in the United States and/or other countries.	standards.
• “Made for iPod” means that an electronic accessory	• iPod is a trademark of Apple Inc., registered in the
has been designed to connect specifically to iPod	U.S. and other countries.
and has been certified by the developer to meet	• iPhone is a trademark of Apple Inc.
Apple performance standards.	• The Bluetooth word mark and logos are owned by
• “Works with iPhone” means that an electronic	the Bluetooth SIG, Inc. and any use of such marks
accessory has been designed to connect	by Victor Company of Japan, Limited (JVC) is under
specifically to iPhone and has been certified by the	license. Other trademarks and trade names are
developer to meet Apple performance standards.	those of their respective owners.

1