Kenwood DT-7000S manual Output Level Screen, Confirm Number Screen, Antenna Signal Screen

Startup Mode Screen

Lock Code Setup

If you have locked any streams in the Channel Lock mode, you will need to enter a 4- digit lock code to unlock them. The factory default lock code is “1 1 1 1”.

You can change the Lock Code to your own preference:

1.While in the Setup Mode, turn the CATEGORY jog dial (unit) or press the

CAT buttons (remote) until the Startup Mode screen appears (right):

1.While in the Setup Mode, turn the CATEGORY jog dial (unit) or press the CAT buttons (remote) until the Lock Code Setup screen appears (top, right):

2.Turn the CH/PRESET jog dial (unit) or press the CH buttons (remote). The Lock Code screen appears (second, right):

3.Using the number buttons, enter the factory default code “1 1 1 1”. The screen’s second line will change from “_ _ _ _” to “* * * *”.

•If you enter an incorrect number, use the left CAT button or jog dial to delete the incorrect number; then re-enter the correct one.

4.Press the MEMO button. The Enter New Lock Code screen appears (right).

•If you entered the code incorrect- ly, “Code Error” will be displayed, and the Enter New Lock Code screen reappears. Repeat Steps 3 – 4.

Lock Code Setup Screen

Lock Code Screen

Enter New Lock Code Screen

2. Use the CH/PRESET jog dial (unit) or the CH buttons (remote) to highlight the screen you want for Startup:

Normal Operation, Channel List (Stream List) or Category List (see pages 7 – 8). Push the SETUP button to exit.

Output Level

You can adjust the DT-7000S’s output level so it matches other sources in your audio system.

1. While in the Setup Mode, turn the
CATEGORY jog dial (unit) or press the
CAT buttons (remote) until the Output	Output Level Screen
Level screen appears (right):

2.Use the CH/PRESET jog dial (unit) or the CH buttons (remote) to select the desired output level.

•“High” is 0dB, “Medium” is –3dB and “Low” is –6dB. Push the SETUP button to exit.

Antenna Signal

This screen shows the quality of the SIRIUS satellite signal that’s being received, to help you find the best location for the antenna.

1.While in the Setup Mode, turn the CATEGORY jog dial (unit) or press the

CAT buttons (remote) until the Antenna

Signal screen appears (right):

5.Using the number buttons, enter your new 4-digit code. The screen’s second line will change from “_ _ _ _” to “* * * *”.

6.Press the MEMO button. The Confirm Number screen appears (below).

7.Re-enter your new 4-digit code. The screen’s second line will change from “_ _ _ _” to “* * * *”.

8.Press the MEMO button. The display

will change to “New Code

Confirmed” Confirm Number Screen

•If you entered the code incorrect-

ly, “Code Error” will be displayed, and the Enter New Lock Code screen reappears. Repeat Steps 5 – 8.

Startup Mode

You can select which screen is displayed when you turn the DT-7000S’s power on.

• After a few seconds the signal
quality bars will indicate how well	Antenna Signal Screen
the antenna is receiving the
SIRIUS satellite signal.

2.Find a location for the antenna that illuminates the maximum number of bars.

•After moving the antenna, wait at least 2 seconds before moving it again, to enable the unit to process the signal.

3.Due to the moving paths of the SIRIUS satellites, it is possible for the signal to change over time. In most cases, signal should be available continuously, however, it may be temporarily blocked in some antenna locations in home installations. Be sure to check the Antenna Signal screen if there is a loss of signal or audio. Experimentation with antenna placement in the home or outside may be necessary to ensure continuous reception.

•See page 5 for information about properly locating the SIRIUS antenna.

12

DT-7000S Instruction Manual