ASA Electronics DV2007 Installation, Before You Begin, Important Notes, Disc Maintenance

Page 3
Screw Stud

DV2007

 

 

Table 1: General Disc Information

 

INSTALLATION

 

 

 

 

 

 

Before You Begin

Disc Type

Logo

 

Diameter/

Playback Time

 

Playable Sides

1.

Disconnect Battery

 

 

 

 

 

 

 

 

 

 

 

 

Before you begin, always disconnect the battery negative terminal.

 

 

 

 

 

 

 

DVD Video

 

 

 

12 cm single/double

133 minutes (4.7 GB)

2.

 

 

 

Remove Transport Screws

 

 

 

 

side

242 minutes (8.5 GB)

 

 

 

 

Important Notes

 

TM

 

 

(1 layer & 2 layer)

266 minutes (9.4 GB)

 

 

 

 

 

484 minutes (17 GB)

Before final installation, test the wiring connections to make sure the unit is connected

 

 

 

 

 

 

Audio CD

 

 

 

12 cm single side

74 minutes

 

 

 

 

properly and the system works.

 

 

 

 

 

 

 

 

 

 

REWRITABLE

 

 

Use only the parts included with the unit to ensure proper installation. The use of

 

 

 

 

 

 

 

unauthorized parts can cause malfunctions.

MP3/MWA Disc

CD-Rs or CD-RWs recorded in MP3, MPEG1 or 2, 2.5 Audio Layer 3 and

 

Consult with your nearest dealer if installation requires the drilling of holes or other

 

WMA Version 7 and 8. The recorded format must be compliant with ISO

 

 

modifications to your vehicle.

 

9660 Level 1, ISO 9660 Level 2, Romeo, or Joliet.

 

 

Install the unit where it does not interfere with driving and cannot injure passengers if

 

 

 

 

 

 

 

 

 

 

 

 

Disc Maintenance

 

 

 

 

there is a sudden or emergency stop.

Before playing, wipe the disc using a clean cloth, working from the center hole towards the

If the installation angle exceeds 30º from horizontal, the unit might not give optimum

 

performance.

outside edge.

 

 

 

 

 

 

 

 

 

 

 

Avoid installing the unit where it will be subject to high temperatures from direct sunlight,

Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.

 

hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

 

 

 

 

 

 

Be sure to remove the control panel before installing the unit.

 

 

 

 

 

 

 

 

 

 

Insert label

Do not bend.

Never touch

Wipe clean from

side up.

 

 

the under side

the center to the

 

 

 

of the disc.

edge.

 

 

 

 

 

NOTE: A disc may become scratched (although not enough to make it unusable)

DIN Front/Rear Mount

This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear” (DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis) mount. For details, refer to installation methods A and B.

DIN Front Mount (Method A)

 

1.

Remove the detachable front panel, if it is

Dashboard

 

attached to the chassis, by pushing the

 

 

REL button.

Bend Tabs

2.

Slide the mounting sleeve off of the

182

 

chassis if it has not already been removed.

depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player.

If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted on page 4.

53

3.Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily

slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

4.Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

5.Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

6.Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation.

7.After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate,

3

Image 3
Contents DV2007 Incompatible Disc Types Safety InformationDisc Notes Compatible Disc TypesImportant Notes InstallationDisc Maintenance Before You BeginReconnect Battery DIN Rear Mount Method BDetachable Control Panel DCP Audio/Video Connections WiringBasic Operation Audio Menu Tuner Operation Ipod Operation Audio CD Operation Insert and Eject DiscControlling Disc Playback Playing Back Stored Files Programmed Memory PlaybackMenu Button Functions Adding Files to the PlaylistRandom 4/RDM MP3/WMA OperationFile Select Repeat 3/RPTDVD Operation Angle DVD Audio 6/DVD AUDIO, DVD AudioDVD Audio Audio Menu Set Up Menu AS/PS/SET UPLanguage Menu Display MenuExiting the Setup Menu Lock MenuOthers Menu Specificationstroubleshooting ASA Electronics Corporation 071806