Maxon Telecom SM-2000 Squelch Mute Circuit, Squelch Noise Band Pass Filter, Noise Detector

Page 24

MAXON SM-2000 MOBILE

THEORY OF OPERATION

The quadrature detector is also configurable for narrow or wide channel spacing by software control of Q219 and diode D127. These components with R219 parallel R211 to maintain audio output at the proper level for the selected bandwidth.

Q134 inserts wideband squelch adjustment RV102 into the circuit whenever standard filter CF104 is selected. This tends to broaden the filter response and provide the higher frequency noise components needed to activate the squelch.

Squelch (Mute) Circuit

The squelch output is sent to microcontroller pin 7 after processing by the squelch circuits. The squelch circuit consists of a double-tuned BPF (Band Pass Filter) and also a noise detector circuit. Details of these circuits are discussed next.

Squelch Noise Band Pass Filter

The output signal from pin 9 of IC109 (MC3371) is filtered to remove the 455 kHz IF variations. The remaining audio is then filtered by a double-tuned BPF consisting of resonator L228-C191, resonator L229-C193 and coupling capacitor C192. The noise in the IF passband is accepted and voice frequencies are rejected. Any noise present at the filter output is applied to the noise detector via RV103. RV103 is used to set the squelch circuit sensitivity and is normally adjusted to produce a noise squelch opening sensitivity of 10dB to 12dB SINAD.

Noise Detector

The noise detector operating in conjunction with IC109 consists of Q132, Q133, D125, D129, TH101 and their associated biasing components. Noise from RV103 is amplified by an op amp within IC109. This noise sprectrum is further amplified by Q133 and rectified by D125. This output is buffered by Q132 and fed to the SQ IN (IC109 pin 12) through R200. When the mute is activated, (IC109 pin9) goes low to pull the base of inverter Q131 low. Q131 collector goes high thereby signalling the microprocessor to mute the receiver audio.

Low Pass Filter

The audio output of (IC109 pin9) is fed to a LPF (Low Pass Filter) consisting of R206 and C201. This RC attenuates 455 kHz IF energy which normally appears at the output of the FM receiver chip. The audio is then routed to the input of IC406A LPF for audio processing.

Speaker Audio Amplifier

After signal detection and audio filtering, the low level audio is returned to pin 1 of IC108, the Audio PA. IC108, a TDA2003 device, provides sufficient power gain to drive the mobile speaker. Digital transistor Q137 mutes the audio amplifier by grounding R157 when the transistor turns on. When Q137 base is high, the transistor is on and the mobile is muted. Conversely when Q137 is off, the mute is released and audio is heard.

Page-20-

December 98

Image 24
Contents SM-2000 Page Table of Contents Maxon SM-2000 MobileSchematics and Block Diagrams PCB LayoutsSM-2000 Exploded View Specifications Transceiver Nominal PerformanceGeneral Operational Bandwidth BandTransmitter Specfications TX Tone Modulation Characteristics SUB Audible Tones DCSReceiver RX Tone Demodulation Characteristics AccessoriesSubaudible tones CTCSS/DCS Reliability AnalysisIntroduction Unpacking Information Check the carton carefully for the following itemsGeneral Description Description of Controls Description of ControlsSM-2000 Rear Panel Theory of Operation Digital CircuitryCTCSS/DCS Decode Circuits CTCSS/DCS Encoder CircuitEeprom PLL RF Section SM-2150/VHF RX VCO TX VCOOut of Lock Detector PrescalerReceiver RF AmplifierReceiver Audio Circuit Low Pass FilterAudio Amplifier Noise Detect Circuit SQ BoardRF Section SM-2450/UHF UHF TransmitterFrequency Synthesizer Circuit Voltage Controlled Oscillator Circuit First MixerSecond Oscillator- Mixer- Limiter and FM Detector Squelch Mute Circuit Squelch Noise Band Pass FilterNoise Detector Speaker Audio AmplifierTest Setup Transmit TestsSM-2150/VHF Alignment Procedure PLL AlignmentDiscriminator Tuning Receiver Alignment RFSquelch Adjustment Automatic Power AdjustmentCTCSS/DCS Deviation Adjustment Modulation Deviation AdjustmentAlignment Points Diagram SM-2150/VHF SM-2450/UHF Alignment Procedure Page-28 December ∙ Note Release the PTT button when changing channels Page-30 December Alignment Points Diagram SM-2450/UHF Component Replacement Surface Mount ComponentsSurface Mount Removal Surface Mount Component Replacement Surface Mounted Integrated Circuit ReplacementParts List Common to SM-2000 REF # DescriptionDigital Parts Common on Both VHF & UHF Digital Section Band Chart REF # Description FRONT-END PCB Assembly Main Board PartsPage-38 December Page-39 December Page-40 December Page-41 December SM-2450A UHF Band SM-2450C UHF Band SM-2450D UHF Band Band Chart SM-2450E UHF BandPage-44 December Page-45 December Page-46 December Page-47 December Component Pinout Page-49 December Page-50 December Voltage Charts SM-2150/VHF IC409Page-52 December Transistor Voltage Chart Voltage Charts SM-2450/UHF IC404 Page-56 December Trouble Shooting Chart SM-2000 Status Indications & Audible TonesPage-58 December Replacement Module Schematics MMBV109MA-4472 Microphone Schematic Page-61- December Page-62- December Page-63- December Page-64- December SW5 SM-2000 Control HeadSM-2150/VHF Main Board Assy Page-66 DecemberSM-2450/UHF Main Board Assy FrontSM-2000 SM-2150/VHF Exploded View Parts List Intentionally Left Blank