Pin No. | Pin Name | I/O | Function |
| |||
|
|
|
|
|
|
| |
1 |
| VC | O | Output terminal for the center point voltage (1/2 VCC) generated |
| ||
| I | Signal input from detector circuit in the optical |
| ||||
|
|
|
|
|
|
| |
8 |
| FI | I | Signal input of the operational amplifier for F signal |
|
| |
|
|
|
|
|
| ||
9 |
| FO | O | Signal output of the operational amplifier for F signal |
| ||
10 |
| PD | I | Front monitor Connected to the photo diode |
|
| |
|
|
|
|
|
| ||
11 | APCREF | I | Input terminal for the setting of laser power |
|
| ||
|
|
|
|
| |||
12 | TEMPI | I | Terminal for the connection to temperature sensor | Not used this set (OPEN) | |||
13 |
| GND | – | Ground terminal |
|
| |
|
|
|
|
|
| ||
14 | AAPC | O | LD amplifier output terminal of APC circuit |
|
| ||
|
|
|
|
|
| ||
15 | DAPC | O | Not used (OPEN) |
|
| ||
16 | TEMPR | O | Output terminal of the reference voltage for temperature sensor | Not used this set (OPEN) | |||
|
|
|
|
| |||
|
|
|
|
|
|
|
|
17 |
| XRST | I | Reset signal input from the system controller (IC600) When reset : “L” | |||
|
|
|
|
| |||
18 | SWDT | I | Write data signal input from the system controller (IC600) |
| |||
19 |
| SCLK | I | Clock signal input from the system controller (IC600) |
| ||
|
|
|
|
|
| ||
20 |
| XLAT | I | Latch signal input from the system controller (IC600) |
| ||
|
|
|
|
|
| ||
21 |
| VREF | O | Reference voltage output Not used this set (OPEN) |
| ||
22 | TENV | O | Not used (OPEN) |
|
| ||
|
|
|
|
|
| ||
23 | THLD | I | Not used (OPEN) |
|
| ||
|
|
|
|
|
|
| |
24 |
| VCC | – | Power supply terminal (+3.3V) |
|
| |
25 |
| TFIL | I | Not used (OPEN) |
|
| |
|
|
|
|
|
| ||
26 |
| TE | O | Tracking error signal output to CXD2535CR (IC200) |
| ||
|
|
|
|
|
| ||
27 |
| TLB | I | Input terminal of the adder signal to tracking error | Not used this set (OPEN) | ||
28 | CSLED | I | Terminal for the sled error lowpass filter |
|
| ||
|
|
|
|
|
|
| |
29 |
| SE | O | Sled error signal output to CXD2535CR (IC200) |
|
| |
|
|
|
|
|
| ||
30 | ADFM | O | FM signal output terminal of the ADIP |
|
| ||
31 |
| ADIN | I | Input terminal by AC coupling is FM signal of the ADIP |
| ||
|
|
|
|
| |||
32 | ADAGC | I | External capacitor connect terminal for AGC of the ADIP |
| |||
|
|
|
|
| |||
33 | ADFG | O | ADIP double turned FM signal output to CXD2535CR (IC200) | (22.05kHz ± 1kHz) | |||
34 |
| AUX | O | Sub signal output to CXD2535CR (IC200) |
|
| |
|
|
|
|
|
|
| |
35 |
| FE | O | Focus error signal output to CXD2535CR (IC200) |
|
| |
|
|
|
|
|
| ||
36 |
| FLB | I | Input terminal of the adder signal to focus error | Not used this set (OPEN) | ||
37 | ABCD | O | Light amount signal output to CXD2535CR (IC200) |
|
| ||
|
|
|
|
| |||
38 | BOTM | O | Light amount bottom hold signal output to CXD2535CR (IC200) |
| |||
|
|
|
|
| |||
39 | PEAK | O | Light amount peak hold signal output to CXD2535CR (IC200) |
| |||
40 | PFAGC | I | External capacitor connect terminal of AGC circuit for the RF |
| |||
|
|
|
|
|
| ||
41 |
| RF | O | Playback EFM RF signal output to CXD2535CR (IC200) |
| ||
|
|
|
|
|
| ||
42 |
| ISET | I | Setting terminal for the internal circuit constant | 22kHz, BPF center frequency | ||
43 |
| AGCI | I | Input terminal by AC coupling is RF signal |
|
| |
|
|
|
|
|
|
| |
44 |
| RFO | O | RF signal output terminal |
|
| |
|
|
|
|
| |||
45 | MORFI | I | Input terminal by AC coupling is RF signal of the MO |
| |||
46 | MORFO | O | RF signal output terminal of the MO |
|
| ||
|
|
|
|
|
| ||
47, 48 |
| I, J | I | Signal input from detector circuit in the optical |
| ||
|
|
|
|
|
|
|
|
– 33 –