6-4. SCHEMATIC DIAGRAM r Refer to page 25 for IC Block Diagrams.
rWaveforms
*Note:
Use R1001 only with Ver.3.0 of microprocessor (IC801). Using R1001 with other micro- processor versions will cause operating errors so be sure to remove it.
You can check the version with Test Mode (page 7).
|
|
|
| 1 |
|
|
|
|
|
|
|
| |
|
|
|
| IC501 | @¥ | VOLT/DIV : 200mV AC |
|
|
|
|
|
| TIME/DIV : 5 μsec |
|
|
|
| 2 |
|
|
|
|
|
|
|
| |
|
|
|
|
| 23∝sec |
|
|
|
|
| IC601 | #» | VOLT/DIV : 1V AC |
|
|
|
|
|
| TIME/DIV : 10 μsec |
|
|
|
| 3 |
|
|
|
|
|
|
|
| |
|
|
|
|
| 482nsec |
|
|
|
|
| IC601 | $Á | VOLT/DIV : 500mV AC |
|
|
|
|
|
| TIME/DIV : 200nsec |
|
|
|
| 4 |
|
|
|
|
|
|
|
| 2.0 |
|
|
|
| 16.9344 MHz | ||
|
|
|
| IC601 | $» | VOLT/DIV : 500mV AC |
|
|
|
|
|
| TIME/DIV : 20nsec |
|
|
| Note: |
|
| |
|
|
| • | All capacitors are in μF unless otherwise noted. pF: μμF | ||
|
|
|
| 50 WV or less are not indicated except for electrolytics | ||
|
|
|
| and tantalums. |
|
|
|
|
| • | All resistors are in Ω and 1/4 W or less unless otherwise | ||
|
|
|
| specified. |
|
|
|
|
| • | C : panel designation. |
|
|
|
|
|
| Note: The components identified by mark !or dotted | ||
|
|
|
| line with mark !are critical for safety. | ||
|
|
|
| Replace only with part number specified. | ||
|
|
| • | A: B+ Line. |
|
|
|
|
| • Power voltage is dc 1.5V and fed with regulated dc power | |||
|
|
|
| supply from battery terminal. |
|
|
|
|
| • Voltages and waveforms are dc with respect to ground | |||
|
|
|
| under |
|
|
|
|
|
| no mark : PLAY |
|
|
|
|
| • Voltages are taken with a VOM (Input impedance 10 MΩ). | |||
|
|
|
| Voltage variations may be noted due to normal produc- | ||
|
|
|
| tion tolerances. |
|
|
|
|
| • | Waveforms are taken with a oscilloscope. | ||
|
|
|
| Voltage variations may be noted due to normal produc- | ||
|
|
|
| tion tolerances. |
|
|
|
|
| • | Circled numbers refer to waveforms. |
| |
|
|
| • | Signal path. |
|
|
|
|
|
| J : PLAY |
|
|
– 21 – | – 22 – | – 23 – | – 24 – |
|
| |