Canon 2000 manual Deluxe Wind Damping System to Stop Gauge Needles Moving

Page 31

Deluxe Wind Damping System to Stop Gauge Needles Moving

If the room pressure gauge fluctuates more than 1 Pa due to the wind and the standard two tube damping system does not reduce them sufficiently then the optional wind damping system may be more effective. The time constant of the system is designed to decrease swings due to wind.

If swings are due to other causes the wind damping system may not help.

Place the Deluxe Wind Damping System case on the ground/floor outside the room or building to be tested. If it has not been stored at the ambient outside temperature, leave it for half an hour to acclimatise before starting the test. DO NOT let the sun or any other heat source beat on the capacity tank.

Plug the RED tube coming from the panel into the smallest connector (of the five) on the back of the capacity tank.

Place the wind damping system in a box and close it up. The box must be on the opposite side of the doorway from the pressure gauges and away from the air blast of the door fan and the wind. This is very quick and often sufficient to stop fluctuations.

Observe the gauges. If still fluctuating more than 1 Pa, attach CLEAR tubes (in any combination of lengths) to each of the four 900 connectors on the back of the capacity tank. Lead the CLEAR tubes to areas around the enclosure as far away from the walls as possible. Lay the tube flat on the ground and cover the ends with cardboard to stop air movement at the end of the tube. DO NOT seal the tube ends.

Observe the gauge needle for at least 30 seconds with the blowers off to ensure wind effects are understood then turn on the blower to establish the required pressure. Again, observe for at least 30 seconds. Some experimentation may be necessary to get the best gauge readings.

CAUTION: Do not allow tube ends to dip into water because this will seal them off.

If the wind fluctuations are still too great.

Increase test pressure so the wind fluctuations are no more than 20% of measured pressure. Do not try to measure the static pressure at time of door fan test. Call it zero.

Take the room to the same positive and negative test pressure. Observe the readings for 60 seconds and take the average.

This procedure will give a slightly (5 to 20%) greater leakage area than a no wind test which will reduce the retention time by 5 to 20% making the test failsafe.

2000 Fire Door-Fan Manual

updated 2002-05-28

Page 31 of 58

Image 31
Contents Fire Door-Fan Manual Fire Door-Fan ManualRun from CA2001 Single Blower Panel Set Up Fire Door-Fan Manual Fire Door-Fan Manual Power to console comes from Set up Model N digital consoleFire Door-Fan Manual OR, Model L digital control panel for Models L64 and L63 Screwdriver supplied. Do not turn more than 3 turns OR, Model E analog gauge clipOR, DM-1 digital gauge for models J64 Fire Door-Fan Manual Fire Door-Fan Manual Fire Door-Fan Manual Fire Door-Fan Manual Large room testing with 2 Blowers Or, E43 Aluminum Frame Set Up Fire Door-Fan Manual Leak Check Smoke test & measure static pressure Principles of Infiltrometer Air Flow Measurement Select Blower RangeChanging Ranges Cannot Achieve Desired Room Pressure with Plate Off Range Selection ProcedureRange Selection When Conducting a Single Point Nfpa Test Range Selection When Conducting a Multi-Reading TestFlow Range Diagram Updated Gauge Reading Rules Room and Flow Pressure ReadingsAnalog Gauge Readings Tubing ConnectionsTaking Readings from Two Blowers Gauge readingsFor models N64, N63, L64, L63, J64, J63 Model DM-1 Digital GaugeTips Time AveragingFire Door-Fan Manual Updated View from outdoors Windy ConditionsUse averaging on digital gauge to reduce the effect of wind Deluxe Wind Damping System to Stop Gauge Needles Moving Fire Door-Fan Manual Enclosures with excessive upper leaks Enclosures with excessive leaksIncrease agent quantity? Reduce the Minimum Protected Height Improper training of testing technicianEliminate Static pressure during retention Reduce High Static Pressures if presentFlex duct installation for ceiling neutralization Ceiling tile is removed to allow the flex duct to be mounted Lower leak tests using Plastic-on-Ceiling procedure Fastest Way to Seal the Ceiling or Register Grilles Conducting the TestLower leak Estimates using Leak audit Field calibration check with calibration plate Fire Door-Fan Manual Tall doorways Packing up and moving equipment Fire Door-Fan Manual Large building Testing Recalibration of Retrotec Infiltrometer Retrotec Gauge and System Calibration Gauge calibration procedureAscending pressure Descending Pressure Final pressure Pa Analog Room gauge target pressuresFire Door-Fan Manual BJ30 Self Test Print Troubleshooting, Maintenance, RepairFire Door-Fan Manual BJ30 Print Head Cleaning Balancing Indoor/Outdoor Temperature Readings Fire Door-Fan Manual Possible Mechanical Problems Fire Door-Fan Manual Cleaning Possible Electrical ProblemsRepairs, Warranty and Customer Support Customer Support Returning Items for Factory Service
Related manuals
Manual 4 pages 7.79 Kb Manual 6 pages 43.98 Kb Manual 11 pages 16.03 Kb

2000 specifications

The Canon EOS 2000D, also known as the Rebel T7 in some regions, is an entry-level DSLR that caters to beginners and amateur photographers looking to explore the world of digital photography. Launched as a successor to the EOS 1300D, the 2000D brings a host of features and technologies that make it an appealing choice for those stepping up from smartphone photography.

One of the standout characteristics of the Canon 2000D is its 24.1-megapixel APS-C CMOS sensor. This high-resolution sensor enables users to capture stunningly detailed images with vibrant colors and rich tonal range. Coupled with the DIGIC 4+ image processor, the camera delivers improved performance in terms of image quality, low-light capability, and overall processing speed.

The Canon 2000D features a 9-point autofocus system that includes one cross-type point, helping users achieve accurate focus on subjects. While this autofocus system may not be the most advanced in the market, it is sufficient for general photography tasks, including portraits, landscapes, and even some action shots.

The camera boasts a 3-inch LCD screen, which provides a clear interface for composing shots and navigating settings. Although it lacks a touchscreen, it offers straightforward usability that appeals to novice photographers learning the ropes of DSLR operation. The optical viewfinder with approximately 95% coverage allows users to view scenes through the lens for precise framing.

For those interested in videography, the 2000D offers Full HD 1080p video recording at 30 frames per second. While it may not excel in advanced video features, it provides a solid entry point for hobbyists looking to experiment with video content. The presence of built-in Wi-Fi and NFC capabilities allows for easy sharing of images and remote control of the camera via a smartphone app, enhancing the overall user experience.

Additionally, the Canon 2000D supports a range of Canon's EF and EF-S lenses, providing users with the flexibility to explore various photography styles. Its compact and lightweight design makes it highly portable, making it a great companion for travel and everyday photography.

Overall, the Canon 2000D is a versatile and user-friendly DSLR that strikes a balance between image quality, functionality, and ease of use, making it an excellent choice for those embarking on their photographic journey.