Before USE, Equipment Main Power Setting | Marantz TT-15S1 instruction

BEFORE USE

This section must be read before any connection is made to the mains supply.

7Equipment Main Power Setting

Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area.

TT-15S1 can be powered by 120V AC only.

7Copyright

Recording and playback of any material may require consent. For further information refer to the following:

-Copyright Act 1956

-Dramatic and Musical Performers Act 1958

-Performers Protection Acts 1963 and 1972

-Any subsequent statutory enactments and orders

7Do Not Locate in the Following

Places

To ensure long-lasting use, do not locate the TT-15S1 where:

•Exposed to direct sunlight.

•Near to sources of heat such as heaters.

•Highly humid or poorly ventilated.

•Dusty.

•Subjected to mechanical vibrations.

•On wobbly, inclined or otherwise unstable surfaces

•Radiated heat is blocked such as in cramped audio racks.

To ensure proper heat radiation, ensure the below clearance from walls and other equipment.

	Front
	0.2m
0.2m	0.2m

	Side
	0.2m
0.2m	0.2m

7Caution: Do not lose the bearing.

(View from underneath the turntable chassis)

Turntable chassis

Center shaft hole

Bearing

Center shaft

There is a bearing located inside the center shaft hole in the turntable chassis. When the turntable leaves the factory, the center shaft hole is covered with tape to prevent the bearing from falling out. Sometimes after removing the tape, the bearing falls out when the turntable is turned over. If the center shaft is inserted when there is no bearing in the center shaft hole, the turntable will not rotate. Therefore, make sure that the bearing does not fall out of the center shaft hole when assembling the turntable.

Furthermore, if the turntable is disassembled for transportation etc. cover the center shaft hole with tape etc. to prevent the bearing from falling out.

7Before using

•Thoroughly remove dust or dirt from the stylus point and record.

If you play records when there is dirt/dust on the stylus, not only will the stylus have poor contact with the record causing poor sound quality, it will also increase the rate of wear of both the stylus and record. Gently remove dirt/dust by brushing with a soft tipped brush from the base of the stylus to the tip. Also wipe the record with a good quality record cleaner.

•Install the turntable chassis and turntable so that they are level.

It is possible to adjust the height of the legs by rotating them. However, as there are only 3 legs, the height may not be adjustable in some cases.

In such cases, adjust the rack itself so that it is horizontal.

• About howling and hum

Howling occurs when sound from the speaker or vibration is transmitted to the player and is picked up by the cartridge again. If howling occurs when the volume is increased, check the positions of the speakers and turntable, and move them to locations where neither vibration nor sound is transmitted to the turntable. Hum noise occurs because of electromagnetic waves that are generated from other electronic devices. Check the position of other electronic devices that are near to the turntable, especially the amplifier. Also, hum or noise occurs if the ground is not connected correctly. Check that the ground wire is securely connected to the GND terminal on the amp/mixer.

TT-15S1 specifications

The Marantz TT-15S1 is a high-performance turntable that combines sophisticated engineering with elegant design, appealing to audiophiles and vinyl enthusiasts alike. This model showcases Marantz's commitment to quality audio reproduction, delivering an immersive listening experience that brings your favorite records to life.

One of the standout features of the TT-15S1 is its belt-driven design, which helps to minimize motor noise and vibrations that can affect sound quality. The turntable utilizes a precision-engineered aluminum platter, which is both lightweight and rigid, ensuring that it maintains stability during playback. The platter is also equipped with an innovative damping system that significantly reduces resonance, further enhancing audio fidelity.

At the heart of the TT-15S1 is its advanced tonearm. The tonearm features a unique carbon-fiber construction that balances strength and weight, contributing to excellent tracking performance. This enables the cartridge to maintain optimal contact with the vinyl grooves, resulting in improved detail and clarity. The turntable also comes with an adjustable counterweight, allowing users to fine-tune the tracking force for different cartridges and vinyl records.

The Marantz TT-15S1 ships with the acclaimed Clearaudio Virtuoso Wood cartridge, known for its warm tonal characteristics and exceptional tracking ability. This high-quality cartridge is designed to extract every nuance from the vinyl grooves, providing a rich and engaging listening experience. The synergy between the cartridge and tonearm design in the TT-15S1 is one of the key factors that make this turntable a standout in its class.

In terms of build quality, the TT-15S1 features a beautifully finished MDF cabinet, which not only enhances its aesthetic appeal but also helps to reduce external vibrations that could interfere with playback. The turntable is available in a sleek black or white finish, allowing it to complement a wide range of audio setups and home décor.

Another notable characteristic of the TT-15S1 is its ease of use. The turntable is equipped with a convenient auto-start and auto-stop functionality, simplifying the playback process for users. The straightforward setup allows even those new to vinyl to quickly enjoy their favorite records without technical hassle.

Overall, the Marantz TT-15S1 is a remarkable turntable that offers a blend of advanced technology, superior craftsmanship, and elegant design. Its combination of features ensures high-fidelity sound reproduction, making it an ideal choice for anyone looking to elevate their vinyl listening experience.