Motorola ENHANCED CELLULAR TELEPHONE owner manual Programming Scanning Modes, Overview

Page 58

Programming Scanning Modes

Overview

The characteristics that determine the way your phone operates in the Cellular System are determined by the Scanning Mode programmed for your phone.

Reviewing / Changing Scanning Mode

Typically, the scanning mode for your phone is programmed by your Service Provider. However, you may review the current scanning mode and (if desired) change it by following these procedures.

To Review Scanning Mode

1.Press RCL , . The display will show the current active system choice.

2.Press END to exit without changing selections.

To Change Scanning Modes

1.Press RCL , . The display will show the current active system choice.

2.Repeatedly press or to cycle through the scanning modes.

3.When the desired scan setting appears in the display, press STO .

4.Press END to exit to normal operation.

NOTE Constant ﬂashing of RM, or a steadily lit NS while within your home service area may indicate an unintentional choice has been made. If this occurs, review the System Type to see if the unit is operating in Standard Mode, or if an alternate selection has been made.

44

Image 58

Contents N e r ’s M a n u a l Warranty Expiration Date Date of Purchase Table of Contents Storing Numbers in Memory Advanced Memory Dialing FeaturesSpecial Call Features Placing Calls From MemoryUsing the Feature Menu Special System FeaturesSelecting and Deselecting Features Cellular System Information Call TimersSecurity Features Programming Scanning ModesTroubleshooting ReferenceIntroduction Vii Viii Introduction Controls and Indicators ➋ Earpiece➏ Numeric Keypad Xii Prepare the Battery for Initial Use Getting StartedLift the battery off Attach the BatteryRemove the Battery Turn your phone offUsing Plug-In Chargers Quick-Change Battery Removal/ReplacementTurning Phone On and Off Basic OperationAbout the Antenna Start-up Self TestsNS No Service Indicator Start-up Status IndicatorsIU In Use Indicator RM Roam IndicatorPlacing a Call To Correct an ErrorWith power on, enter the number you wish to call If Entering More Than 10 DigitsCellular System Busy Automatic RedialingUnsuccessful Call Attempts Complete the CallReceiving a Call Ending a CallPress END Call In Absence Indicator Signal Strength MeterAdjusting Ringer Volume Volume MeterAdjusting Earpiece Volume Low Battery WarningBattery Voltage Meter Press FCNStoring a Phone Number Storing Numbers in MemoryAbout Memory Etc Location entered is displayed to conﬁrm storageEnter the area code and preﬁx you wish to store Press STO Memory Protect FeatureStoring an Area Code and Preﬁx Postscripting EtcDeleting a Memory Entry Changing a Memory EntryAbout Recalling from Memory Placing Calls From MemoryPlacing Calls by Entering Two-Digit Number Placing Calls by Scrolling Last Number Redial Advanced Memory Dialing FeaturesTurbo Dial Feature Recalling Last Number CalledSuper Speed Dial Feature Priority CallScratch Pad Memory Two-Part Tone DialingMemory Linking Example of Memory LinkingEnter the PIN number and # sign Or recall it from memory location RCL , x Create a pauseEnter the account number and # sign Press RCL , SND to send each remaining number group Microphone Muting Special Call FeaturesDisplay Own Phone Number Automatic AnswerHands Free Operation Multiple Key AnswerDistinctive Ringer Multiple Language Display Extended Talk TimeCalling Line ID Special System FeaturesAbout Special System Features Receiving Calls with Calling Line IDRecalling/Viewing Calling Line ID Messages Placing a Call to a Calling Line ID NumberDeleting an Individual Message Other Messaging ServicesStoring a Calling Line ID Number in Memory Deleting All MessagesReminder Beeps Placing a Call using PIN OperationVOX Operation PIN Code OperationSpecial System Features About the Feature Menu Using the Feature MenuSelecting and Deselecting Features Distinctive Ringer Automatic Display TimerOne Minute Beep Automatic AnswerReminder Beeps VOX modeExtended Talk Time Language SelectAlternate Status Review CalloffIndividual Call Timer Call TimersAbout Timers Resettable Call TimerAutomatic Display Timer Electronic Lock Security FeaturesAbout Security Codes To LockChanging the Unlock Code Setting Outgoing Call RestrictionsDisplaying the Unlock Code Automatic LockDescription Display Cellular System Information Service AreaWeak Signal Alert Cellular System OverviewSwitchhook and Advanced System Services RoamingTwo-System Operation System Type and Phone Number DisplayProgramming Scanning Modes Reviewing / Changing Scanning ModeTo Review Scanning Mode OverviewScanning Modes SCAn mode, press Troubleshooting Before Calling For ServiceRegulations and Precautions ReferenceReference Message Glossary CumulFull REMind MSgOFF Reminder Beeps feature disabled REMind MSg On Index Reference Reference Volume Meter VOX Operation Weak Signal Alert Why the concern? Reference Reference Reference Where can I find additional information? Patent Information PAT02250 Quick Reference Card Rbrc