INTRODUCTION:
Congratulations on purchasing a Gemini
FEATURES:
•±6% Pitch control
•Strobe illuminator
•
•Cartridge included
•Fully electronic braking for quick stops
PRECAUTIONS:
1.Read all operating instructions before using this equipment.
2.To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please contact the Gemini Service Department or your authorized dealer to speak to a qualified service technician.
3.Tone Arm bearings are factory set and sealed. Any attempt at adjustment will void the warranty.
4.Be sure that all AC power is OFF while making connections.
5.Cables should be low capacitance, shielded and of proper length. Make sure that all plugs and jacks are tight and properly connected.
6.Always begin with the audio level faders/volume controls set at minimum and the speaker volume control(s) set to OFF. Wait 8 to 10 seconds prior to turning up the speaker volume to prevent the transient “POP” that could result in speaker/crossover damage.
7.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
8.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
PARTS CHECKLIST: |
|
Turntable unit | 1 |
Dust cover hinges | 2 |
Turntable platter | 1 |
45 RPM adapter | 1 |
Rubber mat | 1 |
Counter balance | 1 |
Dust cover | 1 |
Headshell | 1 |
Cartridge | 1 |
ASSEMBLY AND |
|
NOTE: SEE FIG. 1 FOR PART NUMBERS AND LOCATIONS. |
|
VOLTAGE SELECTION:
Rotate the PLATTER (2) until the VOLTAGE SELECTOR (3) (located on the TURNTABLE BASE (1)) is visible through one of the platter holes. Make sure that the VOLTAGE SELECTOR (3) switch is set to the correct voltage.
WARNING: IF YOU TRY TO OPERATE THE TURNTABLE WITH THE INCORRECT VOLTAGE SETTING, IT CAN DAMAGE YOUR TURNTABLE.
ATTACHING THE TURNTABLE BELT:
The TURNTABLE BELT (4A) comes attached to the PLATTER (2) and the MOTOR SPINDLE (4B) but can some times detach in shipping. Rotate the PLATTER (2) and look through the platter holes to check if belt detached. If the belt is not wrapped tightly around the platter and the MOTOR SPINDLE (4B), you need to reattach it.
1.First, place a screwdriver in the center of LOCKING WASHER (4C) around the CENTER SPINDLE (4) and gently pry the washer off.
2.Remove the platter and wrap the belt around the inner circle under the platter. DO NOT STRETCH OUT THE BELT.
3.Replace the platter and rotate the PLATTER (2) until the MOTOR SPINDLE (4B) is visible, then fit your fingers in hole on the top of the PLATTER (2), feel for and grab the rubber belt and attach to the motor spindle.
4.Replace the locking washer.
TURNTABLE INSTALLATION:
1.Put the RUBBER MAT (5) on the PLATTER (2).
2.Set the TURNTABLE BASE (1) on a flat, level surface free of vibration. Use the turntable feet to horizontally stabilize the unit.
3.Try to place the unit as far away from the speakers as possible.
4.Keep the unit away from direct exposure to the sun, heat, moisture or dirt.
5.Keep the unit well ventilated.
CARTRIDGE INSTALLATION: (SEE FIG. 2)
Because all cartridges have their own designs, please refer to your particular cartridge’s instructions to insure proper installation.
1.Connect the lead wires to the cartridge terminals. For your convenience, the terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color.
White (L+) | Left Channel + |
Blue | Left Channel - |
Red (R+) | Right Channel + |
Green | Right Channel - |
2.Mount the cartridge in the HEADSHELL (6) and tighten it with the screws included with the cartridge.
ATTENTIONSTANTON680CARTRIDGEUSERS
When using a Stanton 680 or similar cartridge, where the body is grounded to a cartridge terminal, remove the grounding strap from the cartridge body to the cartridge ground terminal. Failure to do this may result in excessive hum.
HEADSHELL INSTALLATION:
Insert the HEADSHELL (6) into the front of the tubular TONE ARM (7). While holding the HEADSHELL firmly in a horizontal position, turn the LOCKING NUT
(8)counter clockwise until the HEADSHELL is locked in place.
COUNTERWEIGHT INSTALLATION: (SEE FIG. 3A & 3B)
1.Slide the COUNTERWEIGHT (9) onto the rear of the TONE ARM (7) with the numbered stylus gauge facing forward.
2.Twist the COUNTERWEIGHT (9) lightly counter clockwise, to screw it onto the rear of the TONE ARM (7).
ADJUSTING HORIZONTAL ZERO (0) BALANCE AND STYLUS PRESSURE:
1.Without touching the stylus tip, remove the stylus protector (if your cartridge has a detachable one).
2.Release the ARM CLAMP (10) and lift the TONE ARM (7) off the ARM REST (11).
3.Counter clockwise advancement of the COUNTERWEIGHT (9) will cause the cartridge side of the TONE ARM (7) to be lowered. Clock wise will cause the opposite. Turn the COUNTERWEIGHT clockwise or counter clockwise as needed until the TONE ARM (7) is balanced horizontally. You can easily tell this by watching for the point where the TONE ARM (7) “floats” freely.
4.Place TONE ARM (7) on ARM REST (11) and lock it in place with the ARM CLAMP (10).
(4)