Gemini CDM-3600 manual Troubleshooting, Specifications, Fader Replacement

MIXER SECTION: (CONTINUED)

		the tone of each CHAN-
31	3 BAND EQUALIZER: The 3 BAND EQUALIZER adjusts
	NEL by giving you a choice 3 frequencies (BANDS) to adjust , from LOW,
	MIDRANGE (MID) and HIGH’s ,you can use the adjustment knobs to higher or
	lower the 3 seprate frequencies till the sound of the music program is approp-
32	priate for your listening enviroment.
	CHANNEL VOLUME FADER: After you have chosen which input you will use with
	the INPUT SELECTOR the corresponding CHANNEL FADER will allow you to ad-
33	just the volume for that particular CHANNEL.
	CHANNEL CUE SELECTOR: The CHANNEL CUE SELECTOR allows you to choose
	which channel you wish to monitor in your headphones, to the left is CHANNEL
34	(1) to the right is CHANNEL (2).
	CUE VOLUME ROTARYKNOB: The CUE VOLUME ROTARYKNOB adjusts your
	HEADPHONE MONITOR OUTPUT’S volume.
35	MICROPHONE VOLUME ROTARYKNOB: Allows you to adjust the
	volume of the microphone signal.
36	MASTER OUTPUT ROTARYKNOB: The MASTER OUTPUT rotary knob adjust
	the volume of the MAIN MASTER output.
37	VU METER: The CDM-3600has a stereo VU METER that allows you to monitor
	the decible levels of the LEFT and RIGHT MASTER output.
37	FADER START BUTTON: The Fader Start function allows you to start CD play-
	back simply by moving the CROSSFADER from side to side.
	A. Cue up the CD player you wish to start using the Fader Start function
	B. Move the CROSSFADER all the way to the opposite side of the CD
	you have just Cued.
	C. Press the FADER START SELECTOR button so that the button
	becomes illuminated.
	D. At the point which you wish to start the audio from the Cued CD,
	simply move the CROSSFADER in the direction of the Cued CD player,
	and playback will begin.
	E. When the CROSSFADER is moved all the way to the opposite side of
	the currently playing disc, the unit will stop playing that disc and return to
37	the beginning of the track or the set cue point.
	CROSS FADER: The CROSS FADER allows you to mix evenly from one source to
	another. The CROSS FADER on the CDM-3600is also removable and if the need
	arises can be replaced.The RG-45 (RAILGLIDE™) DUAL-RAIL CROSS FADER,

which has internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end can be purchased from your local GEMINI dealer.

NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.

CDM-3600

TROUBLESHOOTING:

-If a disc will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc.

-If the disc turns but there is no sound, check the cable connections, if they are ok, check your amplifier or reciever.

-If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many cd’s are recorded out of spec and will skip on most or all CD players. Before sending the unit for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:		Compact Disc Player
Type
Disc Type	Standard Compact discs (12 cm & 8 cm)
Time Display	Track Elapsed, Track Remain, or Total remain
Variable Pitch	± 12% Slider with Resume Switch
Pitch Bend		± 16% Maximum
Instant Start		Within 0.03 seconds
Installation		19" each
Dimensions	19" x 3.5" x 10" (482.6 x 88.9 x 254 mm)
Weight	Main unit: 11.35 lbs. (5.14 kg)
AUDIO SECTION:	1 Bit Linear/Channel, 3 Beam Laser
Quantization
Oversampling Rate		8 Times
Sampling Frequency		44.1 kHz
Frequency Response		20 Hz to 20 kHz
Total Harmonic Distortion	...................................................	Less Than 0.05%
Signal to Noise Ratio		85 dB
Dynamic Range		85 dB
Channel Separation		85 dB (1 KHz)
Output Level		2.0 +/- 0.2V R.M.S.
Power Supply	AC 115/230V, 60/50 Hz
INPUTS:		3mV,47 KOhm
Phono
Line		150 mV, 27 KOhm
MIC	1.5 mV, 1 KO balanced
OUTPUTS:		20V Peak-to Peak
Max
Rec		225 mV, 5 KOhm

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH-

OUT NOTICE FOR PURPOSE OF IMPROVEMENT.

FADER REPLACEMENT:

1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE SCREWS (C) CAREFULLY REMOVE OLD CROSS FADER AND UNPLUG CABLE (D)

2. PLUG IN THE NEW CROSS FADER INTO CABLE

(D) AND PLACE BACK INTO MIXER.

3.SCREW THE CROSS FADER TO MIXER WITH THE FADER PLATE SCREWS (B)

4.REPLACE THE FACE OF THE MIXER AND SCREW THE FOUR SCREWS BACK IN AND REPLACE THE FADER KNOBS.

6