Sierra Wireless 20070914 manual Reliable UDP

Page 81

Data Communication and Host Modes

Tip: It is best to ensure the idle time-outs for TCP and UDP are never 0 if you're going to be using auto-answer, or either PAD mode. In those circumstances, you will want the modem to close the socket if the connection goes idle for too long, particularly if the other side doesn’t normally close the connection.

When the session is initiated by serial data, the new session will be established using the destination address specified in S53. The S53 setting can be changed if the connect to last UDP setting (*UDPLAST=1) is set. The address in S53 will be updated to reflect the address of the last session initiated by an incoming UDP packet. So that when new data is received over the host serial port while in the idle state, a session will be re‐ established with the last address. (This behavior is the same as the previous Hybrid2 (MD6) mode).

Tip: TCP auto answer (S0) may also be set simultaneously with UDP auto answer. Then, when in the idle state, the modem will accept either a TCP or UDP incoming packet, and enter a TCP or UDP session as appropriate.

Reliable UDP

Reliable UDP adds a simple protocol on top of UDP to provide reliable delivery of data. When data is received from the host serial port, a 2 byte header is added to the data, containing a message type and a sequence number. The PinPoint X will continue to send this data (buffering any received data in the meantime) until it receives an acknowledgement with this sequence number. If an acknowledgement is not received within the time‐out period (specified in S7), the data will be retransmitted. This will continue until an acknowledgement is received or the modem is reset. Likewise any UDP packets received by the PinPoint X are expected to have this simple header. The PinPoint X will issue an acknowledgement for any valid packets which are received.

To configure the PinPoint X for a normal UDP session, you need to set the Startup Mode Default to 73 (ATMD73). If you are using two modems, configure the Destination IP and Port in each to point to each other. Serial data will then be sent reliably between the two.

Caution: Although it adds reliability, the simple implementation of the

Reliable UDP mode in the does not check for duplicate packets.

 

 

 

 

 

 

 

Rev 3.0B Feb.08

 

 

 

 

 

68

 

 

 

Page 80 Page 82
Image 81
Page 80 Page 82
Contents User Guide Important Notice Safety and Hazards Limitation Liability Patents Copyright Trademarks Revision History Contact InformationContents Configuring your PinPoint X Data Communication and Host Modes Snmp Simple Network Management Protocol Configuration Commands Contents Contents Contents PPP over Ethernet PPPoE Aleos Introduction to the PinPoint XAceManager AceWareMonitor and Control Simplified DeploymentAceNet AceViewNetwork Monitoring Modem Doctor Modem Doctor Modem Doctor USBSteps of a connection Connecting to the AT&T NetworkDynamic vs. Static IP Addresses Connecting to the InternetHsdpa Hsdpa CommunicationEdge Specifications Interface Port Pin-Outs Port Power ConnectorActivating PinPoint X on AT&T 3 Network Installating the SIMBefore you start Cellular Account RequiredEjecting the SIM tray Opening the SIM SlotInsert the SIM into the Tray Tools RequiredSample of a Card with SIM Insert the Tray and SIMFinishing the SIM installation Configuring the APNConnect to the Modem Start AceManagerAceManager EDGE/HSDPA Enter the APN10 AceManager Misc Write the Settings to the PinPointIndicator Lights Hardware Installation PinPointGPS Connecting to a Computer or other Device Connecting to PowerSerial Rssi LED Ranges RSSI/Signal LED Status Ranges of Rssi dBm Indicator LightsLight Patterns MountingFront Using AceManager Configuring your PinPointAceManager Connect to Modem Connect to your PinPointAceManager Connected Enter the configuration optionsUsing Templates Write the changes to the modemCreating the Template with AceManager · Cellular Technology specific settings EDGE/HSDPA group Applying a Template to one modem with AceManager Reset the modemConfiguring your PinPoint 10 AceNet Selected modems Choose a name and icon for your connection Using a Terminal Application with AT CommandsConnect To Port Settings serial only15 Port Settings Connected AT CommandsConfiguring your PinPoint Changing the USB port communication Universal Serial Bus USBInstalling the USB driver Set the Port TypeConnect the PinPoint X to your computer’s USB port Hardware Wizard Location options Install the driver from a specific locationVirtual Ethernet Optional Verify and Configure the Virtual Port SettingsSystem Properties Device Manager Ethernet Virtual Serial11 Device Manager Serial 12 Device Manager Driver menu Using the Virtual Ethernet Port Using USB Ethernet with AceManagerUsing USB Ethernet with a Terminal Emulation Utility Using the USB virtual serial port with AceManager Using the Virtual Serial PortUniversal Serial Bus USB Inputs, Relay Outputs, Power Status Capturing External EventsAnalog Inputs Relay Outputs Digital InputsRev 3.0B Feb.08 Inputs, Relay Outputs, and Power Status Connecting devices to the I/O PortWiring Color Corospondance AceManager I/O Monitoring and Setting the I/OGetting Immediate Reports Using RAP Power Modes and InformationWiring the PinPoint X for Power Effect on Modem StateMonitoring Power-In Voltage 11 AceManager Status *POWERIN/*BOARDTEMP Data Communication and Host 8 Modes Basic ModesSerial Modes Start up Mode Basic ModesData Communication AceManager UDP MD AT ModePassThru Mode AceManager PassThru Telnet ModePPP Serial ModesUDP and UDP Pad SlipUDP Auto Answer Reliable UDP TCP and TCP Pad UDP Multicast ModeTCP Auto Answer Hybrid ModesData Communication Public and Private ModeInternal Dhcp Server Keepalive Data usage using Keepalive Configuring KeepaliveIpping Reasons to contact the modem and/or the connected device IP ManagerUnderstanding Domain Names Dynamic Names Car54.mydomain.comCar54.mydomain.com.ca AceManager Dynamic IP Using IP Manager with your PinPointData Usage for IP Manager Server Updates Eairlink.comRestrictions for Modem Name Understanding DNS Configuring DNSAceManager DNS PPP-Peer Domain NameGPS Overview Global Positioning SystemPinPoint X Supported Protocols Remote Access Protocol RAPDatum National Marine Electronics Association NmeaTrimble Ascii Interface Protocol Taip Before you Configure GPS Configuring the PinPoint X forConfiguring the Datum Real-Time Clock SynchronizationOver-The-Air Remote Host TCP GPS Report Polling Local HostAceManager PinPoint *PPTCPPOLL Report TypesSending Reports Automatically Report Delay on Power-UpRemote LocalStore and Forward Store and Forward Reliable Mode11 AceManager PinPoint *PPSNFR, *PPMAXRETRIES Sending Reports Based on an IntervalRAP Configuration RAP Reports Over-The-Air RemoteFlush on Event 15 AceManager PinPoint *PPGPSR RAP Reports over a Local ConnectionDevice ID Configuring Additional RAP FeaturesOdometer Data in Reports Event ReportsCOM 1000 support 22 AceManager *PPCOM1000, *PPREPORTINPUTS Flush on EventMessages Over-The-Air Remote Nmea Configuration26 AceManager Misc S53 Port Streaming Messages Local29 HyperTerminal Nmea Streaming Persistent StreamingTaip Emulation Configuration Taip Command EmulationSupported Taip Commands Rev 3.0B Feb.08 102 35 AceManager PinPoint *PPGPRSR Local ConnectionRev 3.0B Feb.08 104 ‐ *PGPS Sending Unsolicited Taip Messages over the Local ConnectionRev 3.0B Feb.08 106 Snmp Simple Network Management Protocol Management Information Base MIBSnmp Traps Snmp Configuration Listening PortSecurity Level AceManager Change Password menu option User Name and PasswordSnmp MIB Definition Sample Trap DestinationCommunity String Rev 3.0B Feb.08 111 Rev 3.0B Feb.08 112 Rev 3.0B Feb.08 113 Display Responses Product ID Info information Configuration CommandsDEVICEID? HOSTMODE? StatusNETOP? GPS Status and Map Link POWERMODE?Common AT Commands Requiring PassThru modeMisc Miscellaneous +++Dmethodd.d.d.d/ppppp or Dmethod@name/ ppppp DS=n D.d= IP address to contact Ppppp= port to contact ExamplesOPRG=n S53=methodd.d.d.d/pppppMethod= P UDP Method=T TCP Method=N Telnet D.d=IP address =1‐65535Serial STATUSCHK=nUSBDEVICE=n S4=n S3=n=0‐255 =2‐10 seconds=1‐2545 Parity=O Odd Parity=E Even Parity=N None Parity=M Mark=tenths of a second S50=nS51=n S211=nCTSE=n \QnNUMTOIP=n PPPNOCARRIER=nS0=n =seconds =0 ‐=interval ENQ=n AIP=nHOR=n Hh=33 Bsap Hh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCPUDPLAST=n UALL=nUSD=n D.d=IP address of domain serverDynamic IP DNSUPDATE=nDNSUSER=d.d.d.d DOMAIN=nameName=domain name IPMGRUPDATEn=mIPMGRKEYn=key MODEMNAME=nameDHCPSERVER=n PPP/EthernetD.d=local or peer IP address of the modem PassThru String=passwordHOSTPW=string HOSTUID=stringString=AT commands =1‐255 minutes=1‐255 hours NETSMS2EMAIL=n Pw= password=SMS/E‐mail server number SMTPFROM=emailEmail=email address Body=message body SMTPSEND=emailbodySMTPSUBJ=subject Subject=message subjectDAE=n OtherDATZ=n IPPING=nD.d=IP address Name=domain name Name=domain name Port=port=1‐255 seconds =1 On Host=IP address Port=TCP port=minutes Low PowerTPORT=n PTMR=nFriends SISE=nVLTG=n Logging FM=nD.d = IP address DBGDHCPLVL=n DBGCOMMLVL=nDBGETHLVL=n DBGIPLVL=nPinPoint GPS GPSn#IG=n PGPSF=n PGPS=nPPCOM1000=n PPDEVID=n=0‐65535 hex PPLATSEXTRA=n PPLATS=nPPLATSR=n PPMAXRETRIES=n=1‐65535 seconds =meters=5‐255 PPSNFB=n PPSNF=nPPSNFM=n PPSNFR=nPPTIME=n PPTSV=nUDPRGPS=n DIGITALINn? ANALOGINn?IOSTATE=n,s RELAYOUTn=xApn=access point name Edge/HSDPANETAPN=apn Format=2 Numeric Oper=name PPP over Ethernet PPPoE Configuring the PinPoint X for PPPoEOptional Configure *MODEMNAME Configure your PinPoint X to support PPPoEConfiguring a PPPoE Connection in Windows Write the configured settings to your PinPointCreate a new network connection Next Select Connect to the Internet Select Connect using a broadband connection Rev 3.0B Feb.08 167 Select Properties Configure the PPPoE connectionSelect OK until you return to the Connect window 17 PPPoE Connection Connecting to the Internet with PPPoEInstall the driver Installing a modem driver for PinPointWindows Dial-up Networking C DUN Connect the PinPointSelect the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Modem Properties Configure the driverModem Properties Modem Creating a Dial-Up Networking PPP ConnectionRev 3.0B Feb.08 177 Rev 3.0B Feb.08 178 Select Connect using a dial‐up modem Rev 3.0B Feb.08 180 Rev 3.0B Feb.08 181 21 New Connection Finish Configure the DUN connectionCheck Show icon...when connected Rev 3.0B Feb.08 184 Select Advanced Start AceView Connecting to the Internet Using DUNWindows DUN Enable the ConnectionSelect Dial to connect to the modem and the cellular network Start the DUN sessionWindows Dial-up Networking DUN Rev 3.0B Feb.08 189
Related manuals
Manual 176 pages 17.38 Kb Manual 36 pages 19.88 Kb Manual 171 pages 23.08 Kb

20070914 specifications

Sierra Wireless 20070914 is a cutting-edge wireless communication module designed for IoT applications, offering remarkable features and robust performance. This module represents a significant advancement in the realm of embedded wireless solutions, catering to a variety of industries including automotive, industrial automation, and smart cities.

One of the key features of the Sierra Wireless 20070914 is its support for multiple cellular standards, including LTE, which ensures high-speed data transfer and reliable connectivity. The module is designed to operate on various frequency bands, making it versatile and suitable for global deployment. This multi-band capability allows businesses to deploy their IoT solutions in different regions without modification, reducing time-to-market and deployment costs.

Another standout characteristic of the Sierra Wireless 20070914 is its comprehensive and seamless integration with cloud services. The module supports advanced cloud connectivity options, enabling real-time data processing and analysis, which is crucial for industries that rely on timely decision-making. This feature is particularly important in sectors like transportation and logistics, where real-time tracking and monitoring are essential.

The power efficiency of the Sierra Wireless 20070914 is noteworthy. It is engineered to operate optimally in low-power modes, making it ideal for battery-operated devices. This focus on energy efficiency ensures prolonged device lifecycles, supporting the growing demand for sustainable and eco-friendly technologies.

Moreover, the module includes encrypted communication features, enhancing security and protecting sensitive data transmissions. With the increasing prevalence of cyber threats, this security aspect is critical for businesses looking to safeguard their IoT applications from unauthorized access and data breaches.

In addition to these features, the Sierra Wireless 20070914 offers comprehensive development support, including software development kits (SDKs) and application programming interfaces (APIs). This makes it easier for developers to integrate the module into their existing systems, streamlining the development process and accelerating innovation.

Overall, the Sierra Wireless 20070914 stands out as a powerful solution for IoT connectivity, blending advanced technology, security, and efficiency. Its capabilities are designed to support the diverse needs of modern industries, paving the way for future innovations and advancements in wireless communication. As businesses increasingly turn to IoT for modernization, modules like the Sierra Wireless 20070914 will play a crucial role in enabling this transformation.
Top Page Image Contents