RCA RTD250 user manual Operating Your Receiver, Remote Control

Operating Your Receiver

Remote Control

Please be sure you have inserted the batteries into the remote control (see relevant section on page 3.) You can test it by pressing any button. If it works, the red LED will light.

7. Adjustment Buttons

•In all mode except DVD, press OK key will enter into function setting mode, for DVD mode, press and hold the OK key is needed.

•Press OK for DIMMER mode and level adjustment.

• When the display shows the setup you want to change (dimmer, speaker level,	EN
etc), press the left and right arrow buttons to choose, and press up and down
buttons to make changes, then press OK to finalize your choice.

8. Number Buttons

2

4

5

21

1

3

11

9

7

•In Tuner mode, to select a preset station.

•In DVD/CD mode, enable pull down menu by INFO*RDS key (Button 15), then press OK key to select field to be adjusted. Press Number Buttons to direct input the settings (e.g. CD track)

•In DVD/CD mode, when there is no OSD info are displayed, press Button 1 to 5 to select disc; when there is OSD showing, press number buttons to adjust set- tings (e.g. CD track)

9. MENU

•In Tuner mode:

-Press TUNER to select band

-Press to store desired frequency in memory. The flashing word PROG in red will appear in display. Input your desired channel number while the word is still flashing and the frequency will be stored. (For details, refer to "Storing Radio Stations” under “Manual Preset” on page 38)

•In DVD mode, press for menu setup for DVD title.

10. Operation Buttons

17

19

13

6

14

18

20

16

15

8

12

10

2

•TUNER, press TUNER on the remote to enter tuner mode. In TUNER mode, you can press TUNER to select band, and press LEFT and RIGHT buttons to tune down or up the radio frequency.

11. RETURN

• Press to go back to previous menu or exit setup menu completely

12. AUDIO

•Press to select the audio channel you like. (e.g. LEFT / RIGHT)

•In Tuner mode, press this button to switch from ST to MONO mode and vice- versa.

•In DVD mode, press to select different audio channel (if available).

13. ANGLE (DVD only)

• Press to select different screen display angles.

14. ZOOM (DVD only)

• Press to select the zoom ratio.

15. INFO-RDS

• Press to display playback information.

16.TITLE-GUIDE

• Press to go to the title menu at DVD mode.

17. DSP

•Press to change the surround sound settings. The display will toggle among any stereo modes (for DTS (DTS stereo), for DOLBY DIGITAL signal (Dolby Digital, 3 Stereo, Stereo), DOLBY PL II MOVIE, DOLBY PL II MUSIC, DOLBY PRO LOGIC EMU-

LATION, DOLBY 3 STEREO, ARENA, JAZZ CLUB, THEATER, STADIUM, DISCO, STEREO)

18. PLAYMODE

• Press to toggle between different playmodes. (Random, repeat, etc.)

19. EQUALIZER

1. ON-OFF

•To turn on or off the receiver and other auxiliary components (see page 14 “Using the Remote to Control Additional Components”).

2. Source Buttons

• To turn on and select various audio/ video sources.

3. CH+, CH- (Channel Buttons)

•To select programmed stations in TUNER mode.

•To skip to the next or previous chapter, track or image in DVD, CD , mp3 and JPEG mode.

4.VOL+, VOL- (Volume Buttons)

• To adjust the volume.

5.MUTE

• To mute / unmute all audio outputs.

6. INPUT

• Press to select VCR or TV input.

•Press to toggle between different preset equalizer mode (only available in stereo mode.).

20. BASS

•To adjust BASS / TREBLE, press this button once to choose either bass or treble, then press LEFT/RIGHT to adjust level. (Bass/ treble adjustment is not allowed for DTS source)

21. CLEAR / SLEEP

• Press once to enter SLEEP mode.

11