Weslo WLTL33205.0 user manual Insert any extra Wire Harness 53 into the right Handrail

Page 6

3.With the help of a second person, position the treadmill with the Uprights (14, 15) in the vertical position as shown. Hold one of the Handrails (4) near the Right Upright (15).

Route the Wire Harness (53) through the bracket on the Handrail (4) and out the large hole on the side of the Handrail. Insert the bracket on the Handrail into the top of the Right Upright (15). Attach the Handrail with two 1” Bolts (16), two 1/4” Washers (32), and two 1/4” Star Washers (7) as shown. Do not tighten the Bolts yet.

Attach the Left Handrail (not shown) as described above. Note: There is not a wire harness on the left side.

4.Hold the Console Base (87) and the Console (11) near the Right Upright (15). Insert the Wire Harness (53) through the indicated plastic tie on the Console Base and up through the hole in the Console Base. Remove the tape from ends of the small wires in the Wire Harness. Set the Console Base onto the Handrails (4). Attach the Console Base with four 3/4” Screws (5) (only two Screws are shown). Start all four Screws before tightening them.

Touch the right Handrail (4) to discharge any static. Locate the two wires in the Wire Harness (53) that have L-shaped connectors on the ends. Press the connectors onto the two tabs on the switch shown in inset drawing 4a.

Connect the other two wires in the Wire Harness (53) to the back of the Console (11) in the locations shown by the arrows in drawing 4. The connectors should slide easily into the sockets and snap into place (see draw- ings 4b and 4c). If the connectors do not slide easily and snap into place, turn the connectors and then insert them. IF THE CONNECTORS ARE NOT INSERTED

PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

5.Set the Console (11) into the Console Base (87). Make sure that no wires are pinched. Attach the Console to the Console Base with six 3/4” Screws (5) in the locations shown. Start all six Screws before tightening them.

Insert any extra Wire Harness (53) into the right Handrail

(4) and right Upright (15). Securely tighten the plastic tie to prevent the Wire Harness from slipping. Then, cut off the end of the plastic tie.

6

3

 

Large

 

 

 

 

Hole

53

 

 

14

Bracket

16

 

 

4

32

 

 

7

 

 

15

 

16

7

 

 

 

32

 

4

11

 

 

 

87

 

 

4

 

53

Tie

4a

Tabs

53

5

 

 

15

 

 

4b

4c

 

5

11

 

 

 

87

 

 

53

 

 

Tie

 

5

5

5

 

4

 

 

15

 

 

Image 6
Contents Call TOLL-FREE QUESTIONS?Model No. WLTL33205.0 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important PrecautionsPage Before YOU Begin Right SideBack Assembly Side ViewInsert any extra Wire Harness 53 into the right Handrail Raise the Uprights 14, 15 to the vertical position Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Diagram of the Console Battery InstallationStep by Step Console Operation Start the walking belt Insert the key fully into the power switchReset the speed control CALS/FAT CalsHOW to Change the Incline of the Treadmill HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesPart Identification Chart R1005B Key Qty DescriptionExploded DRAWING-Model No. WLTL33205.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT