3.Cut the plastic tie holding the cage nut in the upper end of Left Handrail (2).
Position the Left Handrail (2) on the left Upright (14). The lower end of the Left Handrail should be on the outside of the Extension Leg (41) as shown. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the Handrail Bolt yet.
Attach the lower end of the Left Handrail (2) to the Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a 5/16” Washer (32), and a Handrail Nut (82). Do not tighten the Handrail Bolt yet.
Refer to the inset drawing. Attach the Latch Catch (88) and the Latch Catch Spacer (74) to the left side of the Frame (70) with two Screws (55). Do not to overtighten the Screws or you will damage the Latch Catch.
4.Have a second person hold the Console Base (6) and the Right Handrail (57) near the right Upright (14) as shown. Pull any slack wire from the Console Base through the Bracket. Fold the Wire Harness (26) as shown and insert the folded Wire Harness into the Right Upright.
Cut the indicated plastic tie off the Handrail (57).
Make sure that the Wire Harness (26) is inside of the bracket on the Right Handrail (57) and insert the bracket into the right Upright (14). Make sure that the Wire
Harness is not pinched.
5.Set the Console Base (6) on the Left and Right Handrail (2, 32). Thread a Handrail Bolt (15) with a Handrail Washer (16) into the right Upright (14) and the Right Handrail (32). Do not tighten the Handrail Bolt yet.
Attach the lower end of the Right Handrail (32) to the Extension Leg (41) with a 3 1/2” Handrail Bolt (59), a 5/16” Washer (32), and a Handrail Nut (82).
Tighten all parts used in this step and in step 3.
6.Attach the Console Base (6) to the Left and Right Handrails (2, 57) by threading four Screws (55) into the Console Base. After all four Screws have been started, tighten the Screws until they are snug; do not over- tighten the Screws.
7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a safe place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.
3 |
|
|
|
|
| 15 |
|
|
| 16 |
|
|
| 2 |
|
|
| 14 |
|
| 70 |
|
|
74 |
| 41 | 82 |
|
|
| |
55 | 88 | 32 |
|
|
| 59 |
|
4 |
|
|
|
| 6 |
|
|
Bracket |
|
| |
|
| Plastic Tie |
|
| 57 | 26 |
|
| 14 |
| |
|
|
| |
5 |
|
|
|
|
| 15 |
|
| 6 | 16 |
|
| 2 | 32 |
|
| 14 |
| |
|
|
| |
| 41 |
|
|
| 82 |
|
|
|
| 32 |
|
|
| 59 |
|
6 |
|
|
|
57 |
|
|
|
| 55 | 6 |
|
| 2 |
| |
|
|
| |
|
|
| 55 |
6