Weslo WLTL22191 user manual Assembly, Be careful not to pull on the Wire Harness

Page 5

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrench and your own phillips screwdriver

and

adjustable wrench

.

 

Refer to the drawings below to identify the parts used in assembly.

3/4Ó Screw (55)Ð14

Handrail Bolt (15)Ð4

 

Extension Leg

Handrail Washer

 

Screw (34)Ð2

 

 

 

(16)Ð4

 

 

 

 

1. With the help of a second person, carefully raise the

1

 

26

Uprights (14), the Console Base (6), and the Right

 

 

6

Handrail (57), until the treadmill is in the position shown.

 

 

 

 

 

Be careful not to pull on the Wire Harness (26).

 

 

57

Refer to the inset drawing. Insert one of the Extension

 

 

 

Legs (41) into the treadmill as shown. (Note: It may be

 

 

14

helpful to tip the Uprights [14] in the direction shown by

 

 

 

the arrow as you insert the Extension Leg. Make sure

 

 

 

that the Base Pad [36] is on the bottom of the Extension

 

 

 

Leg.) Attach the Extension Leg with an Extension Leg

 

 

14

Screw (34). Be sure to push on the head of the

 

 

 

Extension Leg Screw while tightening it.

 

 

34

 

 

 

 

Attach the other Extension Leg (41) in the same way.

 

 

41

 

 

 

 

 

 

 

 

36

2. Without removing the tape from the Latch (12), attach the

2

14

 

Latch to the left Upright (14) with four 3/4Ó Screws (55).

 

 

 

Spacer

Make sure that the Screws are tight, but do not over-

 

 

 

 

 

tighten them; if the Screws are overtightened, the

 

12

Springs

Latch will not slide smoothly. After the Latch is at-

55

 

tached, remove any visible tape.

 

 

 

 

 

Note: The inset drawing shows how the parts of the Latch

 

 

 

(12) fit together.

 

 

 

 

 

 

 

 

Latch

 

 

 

 

Bracket

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Customer HOT Line QUESTIONS?Model No. WLTL22191 Serial No Important Precautions Table of ContentsPage Left Side Right Side Before YOU BeginLatch will not slide smoothly. After the Latch is at AssemblyBe careful not to pull on the Wire Harness Handrail Bolts yet Wire Harness is not pinchedPerformant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord STEP-BY-STEP Console Operation Diagram of the ConsoleBattery Installation Turn off the power Insert the key fully into the power switchTo turn off the power, simply wait for about six Follow your progress with the monitor displayHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to USE the Hand Weights HOW to Lower the Treadmill for USE HOW to Move the TreadmillTop Maintenance and TROUBLE-SHOOTINGProblem The power turns off during use Problem The walking belt slips when walked on Problem The walking belt slows when walked onProblem The walking belt is off-center Conditioning Guidelines HOW to Measure Your Heart RateExercise Intensity Workout GuidelinesSuggested Stretches Exercise FrequencyQty Description Part LISTÑModel No. WLTL22191Exploded DRAWINGÑModel No. WLTL22191 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents