Weslo WCTL39102 user manual Troubleshooting and Storage, Symptom the Power does not Turn on, Top

Page 10

TROUBLESHOOTING AND STORAGE

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies to your treadmill and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday, 8h00 until 18h30 east- ern time (excluding holidays).

1.SYMPTOM: THE POWER DOES NOT TURN ON

a.Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a CUL-listed surge suppressor, rated at 15 amps, with a 1 mm2 (14-gauge) cord of 1.5 m (5 ft.) or less in length.

b.After the power cord has been plugged in, make sure that the key is fully inserted into the console (see step 1 on page 8).

c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

2. SYMPTOM: THE POWER TURNS OFF DURING USE

Tripped

Reset

a. Check the circuit breaker located on the treadmill frame near the power cord. If the circuit breaker has tripped, the switch will protrude (see the drawing above). To reset the circuit breaker, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console (see step 1 on page 8).

3.SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY

a.Check the batteries in the console (see assembly step 5 on page 6). Most problems are the result of drained batteries.

b. If the speed display does not show a correct reading, remove the key and UNPLUG THE POWER CORD. Remove the four screws from the sides and front of the hood. Carefully remove the hood. Locate the Reed Switch (73) and the Magnet (75) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Screw (53) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood and run the treadmill for a few minutes to check for a correct speed reading.

b

 

1/8”

43

73

75

 

53

 

Top

 

View

 

4.SYMPTOM: THE WALKING BELT SLOWS OR STOPS WHEN WALKED ON

a.Use only a single-outlet surge suppressor that meets all of the specifications described on page 7.

b.Increase the incline of the treadmill (see HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 9).

c.Make sure that you are using proper form when walking on the treadmill (see PROPER EXERCISE FORM on page 6).

d.If the walking belt still slows when walked on, please call our Customer Service Department.

10

Image 10
Contents QUESTIONS? Model No. WCTL39102 Serial NoTable of Contents Important PrecautionsPage Back Before YOU BeginFront Right SideAn adjustable wrench not included AssemblyTighten all Bolts used in steps 1 Proper Exercise Form HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Press the On/Reset button Diagram of the ConsoleInsert the key fully into the power switch Resetbelt. the speed control and start the walkingKey and unplug the power cord HOW to Change the Incline of the TreadmillMeasure your pulse, if desired Symptom the Power Turns OFF During USE Troubleshooting and StorageSymptom the Power does not Turn on Symptom the Walking Belt Slows or Stops When Walked onSymptom the Walking Belt is OFF-CENTER StorageWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. WCTL39102 Qty DescriptionR1003A Ordering Replacement Parts Limited Warranty Product Warranty Registration