Tie | Weslo WCTL39110 instruction

3.See drawing 3a. If there is a plastic tie in the Cage Nut (70) in the Right Handrail (88), remove the plastic tie. Pull 15cm (6 in) of the Wires (21) out of the right Upright (11). Route the Wires into the bracket on the Right Handrail and out of the upper end as shown. (If necessary, use needle-nose pliers to grip the ends of the Wires.) Thread the included plastic tie through the indicated holes in the Right Handrail.

See drawing 3b. Look into the Right Handrail (88) and make sure that the Wires (21) are on the indicated side of the plastic tie. Then, tighten the plastic tie and cut off the end.

See drawing 3c. Insert the bracket on the Right Handrail

(88)into the right Upright (11), with the lower end of the Right Handrail beside the Extension Leg (34). Tighten a Short Handrail Bolt (89) with a Small Handrail Washer

(39)into the upper end of the Upright.

Attach the Left Handrail (1) as described above. Note: There are no wires in the left Upright (11).

4.Attach the lower end of the Right Handrail (88) to the Extension Leg (34) with a Handrail Bolt (91), a Handrail Washer (92), and a Handrail Nut (93) as shown. Do not tighten the Handrail Nut yet. Note: It may be necessary to push on the lower end of the Handrail to align the hole in the Handrail with the hole in the Extension Leg.

Attach the Left Handrail to the left Extension Leg (not shown) as described above.

5.Place the Console Base (46) on the Handrails (88, 1) (the Left Handrail is not shown). Pull out the two Wires (21) just enough to connect them to the two connectors in the Console Base. Plug the Wires fully into the connec- tors. WARNING: Do not disconnect or connect the Wires while the treadmill power cord is plugged in.

See drawing 5b. Thread four Screws (13) into the Right and Left Handrails (88, 1) and the Console Base (46).

Make sure that the Wires (21) in the Right Handrail are away from the screw holes. After all four Screws have been started, tighten the Screws until they are snug; do not overtighten the Screws.

6.Attach the Storage Latch (14) to the left Upright (11) with two Screws (13). Do not to overtighten the Screws.

See step 4. Tighten the Handrail Nuts (93).

7.Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.

3a	3c
	1
	88
	Tie	89
	11	89
		39
21	70	88
	70	11
		11
	11
3b	Tie
	21
88		34
		34
4
		88
	93	34
	93
	92	91
5a
	88	46
		46
	21
5b	21	1
		1
88
	46
	13	13
6
	11
	13
	14

3a	3c
	1
	88
	Tie	89
	11	89
		39
21	70	88
	70	11
		11
	11
3b	Tie
	21
88		34
		34
4
		88
	93	34
	93
	92	91
5a
	88	46
		46
	21
5b	21	1
		1
88
	46
	13	13
6
	11
	13
	14

3a	3c
	1
	88
	Tie	89
	11	89
		39
21	70	88
	70	11
		11
	11
3b	Tie
	21
88		34
		34
4
		88
	93	34
	93
	92	91
5a
	88	46
		46
	21
5b	21	1
		1
88
	46
	13	13
6
	11
	13
	14

3a	3c
	1
	88
	Tie	89
	11	89
		39
21	70	88
	70	11
		11
	11
3b	Tie
	21
88		34
		34
4
		88
	93	34
	93
	92	91
5a
	88	46
		46
	21
5b	21	1
		1
88
	46
	13	13
6
	11
	13
	14