Weslo WCTL34308.0 user manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 19

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

Tripped

Reset

To reset the circuit breaker, wait for five minutes,

and then press the switch back in.

Position

Position

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

65

20

POWER CORD. Remove the three indicated Hood

Screws (20) and two Foot Rail Screws (25). Then,

 

 

 

carefully remove the Hood (65).

 

25

 

 

 

 

Locate the Reed Switch (89) and the Magnet (62) on

 

 

the left side of the Pulley (71). Turn the Pulley until the

1/8 in.

 

Magnet is aligned with the Reed Switch. Make sure

71

that the gap between the Magnet and the Reed

 

Switch is about 1/8 in. (3 mm). If necessary, loosen

89

62

the Reed Switch Screw (3), move the Reed Switch

slightly, and then retighten the Screw. Reattach the

Top View

 

Hood (not shown), and run the treadmill for a few min-

 

utes to check for a correct speed reading.

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model No. WCTL34308.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged Assembly105 Large Hole Small Holes Wire Tie 4954 See the left inset drawing. Identify the outer See the left inset drawing. Identify the twoOuter side of the Frame Spacer facing Washer 9 do not tighten the Colored Patch Frame Bolt yetConsole Wire Tie Bracket Large Hole Tab Guard Raise the Uprights 53, 54 to the vertical posi Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to USE the Manual Mode Measure your heart rate if desired Select one of the four speed programs. To select a speed pro HOW to USE a Speed ProgramHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Walking belt. If the walking belt has shifted to Problem The walking belt slows when walked onExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description Part LIST-Model No. WCTL34308.0Key No. Qty Exploded Drawing A-Model No. WCTL34308.0 R0608A Exploded Drawing B-Model No. WCTL34308.0 R0608A Exploded Drawing C-Model No. WCTL34308.0 R0608A Exploded Drawing D-Model No. WCTL34308.0 R0608A Limited Warranty Ordering Replacement Parts
Top Page Image Contents