Weslo WCTL34308.0 user manual Problem The walking belt slows when walked on

Page 20

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor-

b

2–3 in.

mance may decrease and the walking belt may be-

come damaged. Remove the key and UNPLUG THE

 

 

POWER CORD. Using the hex key, turn both rear

 

 

roller bolts counterclockwise, 1/4 of a turn. When the

 

 

walking belt is properly tightened, you should be able

 

 

to lift each edge of the walking belt 2 to 3 in. (5 to 7

 

 

cm) off the walking platform. Be careful to keep the

 

Rear Roller

walking belt centered. Then, plug in the power cord,

 

insert the key, and run the treadmill for a few minutes.

 

Bolts

Repeat until the walking belt is properly tightened.

 

 

c.If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt has shifted to the left, first re-

 

 

 

 

 

 

 

a

 

move the key and UNPLUG THE POWER CORD.

 

 

Using the hex key, turn the left rear roller bolt clock-

 

 

 

 

 

 

wise 1/2 of a turn. Be careful not to overtighten the

 

 

 

walking belt. If the walking belt has shifted to the

 

 

 

right, turn the left rear roller bolt counterclockwise 1/2

 

 

 

of a turn. Then, plug in the power cord, insert the key,

 

 

 

and run the treadmill for a few minutes. Repeat until

 

 

 

the walking belt is centered.

 

 

 

b. If the walking belt slips when walked on, first re-

b

move the key and UNPLUG THE POWER CORD.

Using the hex key, turn both rear roller bolts clock-

 

wise, 1/4 of a turn. When the walking belt is correctly

 

tightened, you should be able to lift each edge of the

 

walking belt 2 to 3 in. (5 to 7 cm) off the walking plat-

 

form. Be careful to keep the walking belt centered.

 

Then, plug in the power cord, insert the key, and care-

 

fully walk on the treadmill for a few minutes. Repeat

 

until the walking belt is properly tightened.

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents QUESTIONS? Model No. WCTL34308.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged105 Large Hole Small Holes Wire Tie 4954 See the left inset drawing. Identify the two Outer side of the Frame Spacer facingWasher 9 do not tighten the Colored Patch Frame Bolt yet See the left inset drawing. Identify the outerConsole Wire Tie Bracket Large Hole Tab Guard Raise the Uprights 53, 54 to the vertical posi Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord HOW to Turn on the Power Console DiagramFeatures of the Console HOW to USE the Manual Mode Measure your heart rate if desired HOW to USE a Speed Program Select one of the four speed programs. To select a speed proHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Walking belt. If the walking belt has shifted toExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. WCTL34308.0 Qty DescriptionKey No. Qty Exploded Drawing A-Model No. WCTL34308.0 R0608A Exploded Drawing B-Model No. WCTL34308.0 R0608A Exploded Drawing C-Model No. WCTL34308.0 R0608A Exploded Drawing D-Model No. WCTL34308.0 R0608A Ordering Replacement Parts Limited Warranty
Top Page Image Contents