Weslo Cadence DL40 user manual Tighten all parts used in this step and in step

Page 6

3.Cut the plastic tie holding the cage nut in the upper end of the Left Handrail (2).

Position the Left Handrail (2) on the left Upright (14). The lower end of the Left Handrail should be on the outside of the Extension Leg (41) as shown. Thread a Handrail Bolt

(15)with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the Handrail Bolt yet.

Attach the lower end of the Left Handrail (2) to the Extension Leg (41) with a 3 1/2Ó Handrail Bolt (59), a 5/16Ó Washer (32), and a Handrail Nut (82). Do not tighten the Handrail Bolt yet.

4.With the help of a second person, lift the Right Handrail (57) off the right Upright (14). Hold the Console Base (6) and the Right Handrail in the position shown. Feed all of the excess Wire Harness (26) into the Right Handrail, through the indicated bracket, and down into the right Upright; bend the Wire Harness, if necessary.

Cut the indicated plastic tie off the Right Handrail (57).

Make sure that the Wire Harness (26) is in the bracket and insert the bracket into the right Upright (14). Make sure that the Wire Harness is not pinched.

5.Thread a Handrail Bolt (15) with a Handrail Washer (16) into the right Upright (14) and the Right Handrail (57). Do not tighten the Handrail Bolt yet.

Attach the lower end of the Right Handrail (57) to the Extension Leg (41) with a 3 1/2Ó Handrail Bolt (59), a 5/16Ó Washer (32), and a Handrail Nut (82).

Tighten all parts used in this step and in step 3.

6.Attach the Console Base (6) to the Left and Right Handrails (2, 57) with four Screws (55). Align the holes in the Reading Rack (88) with the holes in the Console Base

(6). Attach the Reading Rack with the four Reading Rack Screws (74) as shown.

7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a safe

place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat

6(not included) under the treadmill.

3

 

 

 

15

 

 

16

 

14

2

 

 

 

 

41

 

 

82

 

59 32

 

4

 

 

 

6

 

 

Bracket

Plastic Tie

 

 

 

 

26

 

57

14

 

 

5

 

 

 

 

15

 

 

16

 

57

 

 

 

14

 

41

 

 

82

 

 

 

32

 

 

59

6

88

 

57

 

 

 

6

74

 

 

 

55

2

 

 

 

 

55

Image 6
Contents QUESTIONS? Model No. WLTL51690 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Before YOU Begin Left Side Right SideAssembly Driver , adjustable wrench , and scissorsExtension Leg Screw while tightening it Tighten all parts used in this step and in step Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Insert the key fully into the power switch Diagram of the ConsoleBattery Installation Step by Step Console OperationFollow your progress with the monitor display Reset the console and start the walking beltAdjust the incline of the treadmill as desired Measure your pulse, if desiredHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Maintenance and TROUBLE-SHOOTING Problem The power turns off during useTop Problem The walking belt slows when walked on Problem The walking belt is off-centerProblem The walking belt slips when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Suggested Stretches Part LISTÑModel No. WLTL51690 Key No. Qty DescriptionDRAWINGÑModel No. WLTL51690 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT