Weslo 85 user manual

Page 7

3.Open part bag B. Hold an Upright Spacer (59) against one side of the Frame (96) as shown. Insert a 3 1/2” Bolt (54) into the indicated hole in the Upright Spacer and the Frame. Next, tighten a Crossbar Screw (37) into the Upright Spacer and the Frame. Then, remove the 3 1/2” Bolt. Repeat this procedure on the other side of the Frame.

Have a second person lift the front end of the Frame

(96). Insert a 3 1/2” Bolt (54) with a 3/8” Star Washer (55) into the Right Upright (104) and the right Upright Spacer (59), and tighten the Bolt into the Frame. Do not over- tighten the Bolt. Repeat this procedure on the left side of the Frame.

4.Attach the Latch Housing (46) to the Left Upright (47) with two 3/4” Screws (38). Make sure that the large hole in the Latch Housing is on the side shown.

Remove the knob from the pin. Make sure that the col- lar and the spring are on the pin. Insert the pin into the Storage Latch (46), and then tighten the knob back onto the pin.

5.Feed the Wire Harness (65) up into the bracket on one of the Handrails (40) and out of the large hole in the left side. (Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.) Remove any nylon ties from the bracket.

Insert the bracket on the Handrail (40) into the upper end of the Right Upright (104). Attach the Handrail with two 1” Bolts (43), two 1/4” Washers (44), two 1/4” Star Washers (45), a 4” Bolt (117), and a 5/16” Washer (122) as shown. Do not tighten the Bolts yet.

See drawing 5a. Insert the included nylon tie through the indicated hole in the Handrail (40). See drawing 5b. Look into the Handrail and make sure that the Wire Harness

(65)is secured to the side shown. Tighten the nylon tie and cut the excess off the end.

Attach the other Handrail (not shown) in the same way. Note: You may need to tip the Handrail to one side as you insert the bracket. There is not a wire harness in the left Upright (not shown).

3

104

 

37

55

54

 

96

59

 

 

Hole

4

 

 

47

Knob

 

Large Hole

 

 

 

 

Spring

 

 

38

46

 

Collar

 

 

 

 

 

Pin

 

 

 

 

 

5

 

 

 

Large

 

 

65

 

 

 

 

 

 

Hole

 

 

Bracket

 

43

 

 

 

 

 

44

 

 

40

 

 

45

 

 

 

 

 

 

 

 

 

 

104

 

 

43

44

45

 

117

 

 

 

 

122

 

5a

Tie

 

 

5b

Tie

 

 

 

 

40

 

40

 

 

 

 

 

 

 

 

 

 

65

7

Image 7
Contents Model No. WETL2614.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Right Side Before YOU BeginBack Wheels 63 are in the indicated position AssemblyRight Upright is oriented so the pivot hole is Page Tighten the Crossbar Screws GFCI-equipped outlets Operation and AdjustmentHOW to Plug in the Power Cord Performant Lubetm Walking BeltFeatures of the Console HOW to Turn on the Power Change the incline of the treadmill as desired HOW to USE the Manual ModeSelect the manual mode Insert the key fully into the consoleWhenkey. you are finished exercising, remove Fat Calories/CaloriesInsert the key into the console HOW to USE a Speed ProgramSelect one of the speed programs HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Part Identification Chart Key Qty Description R0705AWETL2614 Ordering Replacement Parts