Weslo 831.294620 user manual Left Upright 46. Do not tighten the Bolt yet, Yet

Page 6

3.Cut the plastic tie holding the cage nut in the upper end of the Left Handrail (45).

Position the Left Handrail (45) on the left Upright (46). Thread a 1/4” x 1” Bolt (42) with a Handrail Washer (43) two complete turns into the upper end of the left Upright and the Left Handrail. Do not tighten the Bolt yet.

Thread a 1/4” x 1” Bolt (42) with a Handrail Washer (43) two complete turns into the lower end of the Left Handrail

(45)and the left Upright (46). Do not tighten the Bolt yet.

4.With the help of a second person, lift the Right Handrail

(59)and hold the right Handrail and the Console Base

(52)near the right Upright (46) as shown. Feed all of the excess Wire Harness (60) into the Right Handrail, through the indicated bracket, and down into the right Upright; bend the Wire Harness, if necessary.

Cut the indicated plastic tie off the right Handrail (59).

Make sure that the Wire Harness (60) is in the bracket and insert the bracket into the right Upright (46). Make sure that the Wire Harness is not pinched.

5.Thread a 1/4” x 1” Bolt (42) with a Handrail Washer (43) two complete turns into the upper end of the right Upright (46) and the Right Handrail (59). Do not tighten the Bolt yet.

Thread a 1/4” x 1” Bolt (42) with a Handrail Washer (43) two complete turns into the lower end of the Right Handrail

(59)and the right Upright (46). Do not tighten the Bolt

yet.

6.Set the Console Base (52) on the Left and Right Handrails (45, 59). Make sure that the Wire Harness (60) is out of the way as you thread four 1 1/4” Screws (11) into the Handrails and the Console Base.

Tighten all parts used in steps 3 and 5. Then, tighten the 1 1/4” Screws (11) used in this step.

3

 

42

 

43

 

 

45

46

 

 

43

 

42

4

 

52

 

Bracket

 

 

Plastic Tie

59

60

 

 

46

5

 

 

42

 

43

59

46

 

43

 

42

 

6

 

60

 

59

 

11

52

 

46

45

11

7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or car- pet, place a mat under the treadmill.

6

Image 6 Contents
Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, IL Table of Contents Important PrecautionsPage Back Before YOU BeginFront Right SideAssembly Careful not to pull on the Wire Harness. Set the RightTwo Screws 2. Be careful not to overtighten Left Upright 46. Do not tighten the Bolt yet YetOperation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Battery InstallationSTEP-BY-STEP Console Operation HOW to Change the Incline of the Treadmill CALS/FAT CalsHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Maintenance and TROUBLE-SHOOTING Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesExercise Frequency Suggested StretchesRemove this Exploded Drawing and Part List from the Manual Part LIST-Model No Qty DescriptionExploded DRAWING-Model No 294620 Full 90 DAY Warranty Model NoSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL