Smooth Fitness FX25 user manual Cleaning, To apply lubricant to the walking belt

Page 32

32FX25 TREADMILL

MAINTAINENCE

CLEANING:

Routine cleaning of your treadmill will extend the product's life.

•Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged from the wall electrical outlet before attempting any cleaning or maintenance.

•Important: Never use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids away and keep it out of direct sunlight.

•After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to remove excess perspiration.

•Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.

DECK LUBRICATION:

The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be lubricated usually within the first 400 hours of use.

Every 2 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below.

Please use Lube 'N Walk (can be purchased from your dealer or call the number on the front of the manual), or a non-petroleum based silicone such as "Napa 8300" (available at most stores).

To apply lubricant to the walking belt:

1.Position the walking belt so that the seam is located on top and in center of the walking board.

2.Insert the spray nozzle into the spray head of the lubricant can.

3.While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board approximately 6" from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.

4.Allow the silicone to "set" for 1 minute before using the treadmill.

Spray lubricant from front to back.

Page 31 Page 33
Image 32
Page 31 Page 33
Contents FX25 Motorized Treadmill Precautions PrecautionsFor future service or related questions Power Requirements Power RequirementsPreassembly Supplied Components Supplied Hardware Complete Parts List Complete Handle Bar ComponentsComplete Upright Components Description Qty Order NoMain Frame Cross BAR 701 Deck Frame 3MM Rubber Cushion Parts Diagram 801 109 102 111 103 108 104 106 107 110 803 105 802807 807 307 308 301 302 110 802 303 304 305 306 14 FX25 Treadmill Parts Diagram 602 604 835 605 601 836 606 838 836 846 603 847 607 703 702 705 704 840 839 841 707 845 828 701 842 818 706 Assembly Unpacking and InventoryAssembly 811Fig-1 Assembly Step 805809 805 812 802 803 Step 802306 Step Stabilizer Adjustment Follow These Instructions to Level Your TreadmillHow to fold up the treadmill Folding InstructionsHow to unfold the treadmill Unfolding InstructionsTransport Instructions Transport InstructionsHOW to Maintain the Momentum G-FIT-FX25 Treadmill MaintainenceCleaning To apply lubricant to the walking beltImportant Steps Before beginningAerobic exercise Target Heart RateFinding your pulse Muscle Chart Targeted muscle groupsStretching Routine Troubleshooting Troubleshooting Treadmill will not startTreadmill looses power during use Treadmill walking belt slows during use888.800.1167
Top Page Image Contents