Saris 911 manual Close and lock track, Check your installation. Be certain, Warranty

Step 7-

Close and lock track.

•Turn knob, at end of each load bar, in direction of orange arrow until the word "LOCK" appears.

•Lock load bar with key.

Step 8-

Check your installation. Be certain:

•Daisy dials are tightened completely against wheel tray and upright bracket. Retighten daisy dial against upright bracket after first two hours of initial use.

•Upright clamp is firmly grasping each bike and is in the closed position.

•Wheel straps are used on both front and rear tires.

•Accessory tracks are closed and locked.

•Load is evenly distributed on load bars. For maximum weight limitations, follow recommendations of vehicle manufacturer.

•The entire system including attachment of load bars to the vehicle is stable and secure. Walk around vehicle to check each attachment clip. Refer to attachment clip instructions for correct clip positioning and proper installation.

Cautions

1)All requirements for compatibility/ fit as stated in the current Saris Vehicle/ Carrier Compatibility Guide must be followed.

2)Check your installation as recommended. Because vehicles and conditions vary, it is your responsibility to insure the safe and proper use of this product. Improper attachment or misuse may result in damage to your carrier, bicycles, vehicle, or vehicles traveling behind you.

3)Use only Saris clips and accessories.

4)When in use, remember carrier is installed!

a)Be aware of low overhead clearances.

b)Do not go through automatic car wash with carrier installed.

c)Occasionally check attachment of carrier and load.

5)Open vehicle doors before removing carrier; failure to do so could damage doors.

6)Replace any part at first sign of fatigue or wear.

Warning and Disclaimer

This carrier has been designed to carry accessories on specific vehicles. Before installation, user must read and follow current Vehicle/ Carrier Compatibility Guide (available through Saris dealer) recommendations and enclosed instructions. Fit recommendations are based on vehicle's standard features; optional features may affect the fit recommendations. User must attach carrier correctly to the vehicle, check its attachment before each use, and inspect carrier parts for wear. Carrier's attachment to the vehicle is critical and beyond the control of the manufacturer. Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this carrier.

Warranty

We warrant this product to the first consumer to be free from defect in material and workmanship for a period of two years from date of purchase. (Please retain your sales slip for your records.) Any product or part thereof found to be defective within that period will be replaced without charge provided that: (1) the product was not misused; (2) no alterations or modifications were made; (3) its failure resulted from a defect in material or workmanship and not from normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Graber Products. Manufacturers only obligation shall be to replace such products or parts proved to be defective.

a special products division of

	5253 Verona Rd.
	Madison, WI 53711
Made in U.S.A.	800-783-7257	Worldwide patents
911-IS 11/99 Revison B	www.sarisproducts.com	issued and pending.

UPRIGHT MOUNT

Bicycle Carrier Model #911

Please READ and FOLLOW all instructions carefully!

	wheel straps
upright arm		clamp
		handle
	upright bracket
	lever	wheel tray

tension screw

attachment block

channel	daisy dials
	(tightens to load bar)
	(tightens to wheel tray)

The Saris Upright Mount Accessory can support bikes

with a tire size between 12-1/2 and 27 inches.

Step 1-

Check load bar placement.

Use of the upright mount requires that your load bar spacing be between

16" (minimum) and 36" (maximum).

Refer to available load bar spacing in clip set instructions. If your available load bar spacing is:

-less than or equal to 36 inches, place load bars following all recommendations in your clip set instructions.

-greater than 36 inches, place load bars 36" apart anywhere along the length of your

vehicle.