Cateye CC-ST200 warranty Mounting to Bike, Limited Warranty, Specifications

CATEYE TOMO XC

CYCLOCOMPUTER

Model CC-ST200

[with Heavy Duty Wire]

	U.S. Pat. Nos. 4636769/4642606/5236759/5226340
E	and Design Patented
	Copyright© 1999 CATEYE Co., Ltd.
	CCMSTxch1-991124 Printed in Malaysia 066600035 3

MOUNTING TO BIKE

1.	Bracket	7.	Sensor Band Rubber Pad
2.	Wire	8.	Bracket Rubber Pad (2 pcs.)
3.	Sensor	9.	Nylon Tie (3 pcs.)
4.	Sensor Bands-A (S)(L)	10. Sensor Band Screw (S)(L)
5.	Sensor Bands-B	11. Spiral Tube
6.	Magnet

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.)

TIRE SIZE	L(cm)	TIRE SIZE	L(cm)	TIRE SIZE	L(cm)
20 x 1.75	150	26 x 1.40	200	650 x 38B	211
24 x 1	175	26 x 1.50	199	700 x 18C	207
24 x 3/4 Tubular	178	26 x 1.75	202	700 x 19C	209
24 x 1-1/8 Tubular	179	26 x 1.95	205	700 x 20C	209
24 x 1-1/4	191	26 x 2.00	206	700 x 23C	210
24 x 1.75	189	26 x 2.1	207	700 x 25C	211
24 x 2.00	192	26 x 2.125	207	700 x 28C	214
24 x 2.125	196	26 x 2.35	208	700 x 30C	217
26 x 1(559mm)	191	27 x 1	215	700 x 32C	216
26 x 1(650c)	195	27 x 1-1/8	216	700C Tubular	213
26 x 1.25	195	27 x 1-1/4	216	700 x 35C	217
26 x 1-1/8 Tubular	197	27 x 1-3/8	217	700 x 38C	218
26 x 1-3/8	207	650 x 35A	209	700 x 44C	222
26 x 1-1/2	210	650 x 38A	212

SPECIFICATIONS

Controller -----------------------------------	4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)
Display --------------------------------------	Liquid Crystal Display
Sensor --------------------------------------	No Contact Magnetic Sensor
Operating Temperature Range -------	0° C - 40° C (32° F - 104° F)
Applicable Cycle Sizes ------------------	130cm - 229cm
The length of the wire -------------------	70cm
Applicable Fork Diameter --------------	11ø - 40ø (S:11 - 26ø L:21 - 40ø)
Power Supply -----------------------------	Lithium Battery (CR1620 or CR1616) x 1
Battery Life ---------------------------------	Approx. 3 years(The life of the first factory-loaded battery may
	be shorter than this period.)
Dimension/Weight ------------------------	1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g)

* The specifications and design are subject to change without notice.

LIMITED WARRANTY

1-Year Warranty for Main Unit Only

(Accessories/Attachments and Battery Consumption excluded)

If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service.

(Address for service) CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn.: CAT EYE Customer Service Section

magnet

sporkes

		Fig.1
	sensor band B
rubber pad		sensor band B
sensor
band A	Fig.2
			rubber pad
sensor band A			sensor band A
		parallel	Fig.3
		screw
sensor fork
	Fig.4	markingline
		of sensor
sensor		center of
		magnet
			Fig.5
	about 2mm
magnet	Fig.6
			outer cable

•The spokes must run correctly through the inside the magnet as in fig.1.

•Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diameter (S size for up to 24ø, L for oversize). If the front fork is thick, use the longer screw.

1.Insert the band-B into the slit of the band- A, and put the rubber pad inside of the band-A(fig. 2). Adjust the length in order that the screw-fastening part of the bands are parallel when mounted to the fork(fig.

3). *To pull out the band B from band A, tug strongly.

2.Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the screw(fig. 4).

3.Align the magnet's center and the sensor's marking line(fig. 5), and make sure of 2mm clearance between the magnet and sensor (fig. 6). Then tighten the screw securely. Cut the excess of the band-B with a nipper or the like.

•Secure the wire with nylon ties as shown in fig. 7. Wind the wire round the outer cable and wrap these wires with the spiral tube. Adjust the length of the wire. Loosen the wire in the area marked with the arrow so that the wire does not hinder handlebar operation.

•Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter. Attach the bracket close to the handlebar stem (fig. 8).

•Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward while pushing down the lever. (fig. 9)

Service & Research Address for United States Consumers:
CAT EYE Service & Research Center
1705 14th St. 115 Boulder, CO 80302
Phone : 303-443-4595	Toll Free: 800-5CATEYE
Fax : 303-473-0006	e-mail: CatEyeUSA@aol.com
#169-9731
Heavy Duty Wire and Bracket Sensor Kit
#169-9771
Bracket Sensor Kit for Extra Large Fork
#169-6168
Bracket Sensor Kit for Aero Bar
#169-6167
Center Mount Bracket Kit
#169-6169
Stem Mount Bracket Kit

spiral tube	•Test
	Mount main unit. If main display does not show
	any figures, press either M button or S/S button
	to release from power saving function. Spin the
	wheel to check if sensor pulse symbol flashes.
nyron ties	If not, adjust relative positions of magnet and
	sensor following the instructions.
wire
Fig.7	lever
bracket	Fig.9

Slide the main unit onto the bracket from front until it clicks into position. To remove it, pull it off forward while pushing down the lever. (Fig.9)

rubber pad

Fig.8

#169-9750	#169-9751
Attachment Kit (For Heavy Duty Wire)	Attachment Kit (For TOMO XC)
#166-5120	#169-6180
Wheel Magnet	Lithium Battery(CR1620)