Cateye CCAT2W-090526 manual Wireless Sensor, Format initialize, Install the sensor and magnet

CATEYE ADVENTURE	ENG
CYCLOCOMPUTER CC-AT200W	0678
U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright© 2009 CATEYE Co., Ltd. CCAT2W-090526 3

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi- tions:(1)This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment.

WARNING / CAUTION

••Do not concentrate on the computer while riding. Ride safely!

••Install the magnet, sensor, and bracket securely. Check these periodically.

••If a child swallows a battery, consult a doctor immediately.

••Do not leave the computer in direct sunlight for a long period of time.

••Do not disassemble the computer.

••Do not drop the computer to avoid malfunction or damage.

••When using the computer installed on the bracket, change the MODE by pressing on the four dots below the screen, or by pressing on the SSE simultaneously, to start or stop the timer. Pressing hard on other areas may result in malfunction or damage to the computer.

••Be sure to tighten the dial of the FlexTight bracket by hand. Tightening it strongly using a tool, etc. may damage the screw thread.

Before using the computer, please thoroughly read this manual and keep it for future reference.

••When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

••A temperature sensor is built in the computer. If the sensor is heated by direct sunlight or body heat, it may not indicate the temperature correctly.

••The altitude data with this unit is for reference only; accordingly, do not use this unit as a measuring device for professional use.

••Dispose of used batteries according to local regulations.

••LCD screen may be distorted when viewed through polarized sunglass lenses.

Wireless Sensor

In order to prevent any interference with the sensor signal, the transmission range is designed to be 20 to 70 cm, in addition to use of the ID code. (This receiving range is only a reference.) Please note the following points.

••To use this unit, the sensor ID has to be set.

•• Two different IDs, ID1 and ID2, can be registered to this unit, which are identified automatically.

••The computer cannot receive when the distance between the sensor and computer is too long. Temperature drop and battery drain may worsen the receiving sensitivity even if they are within the transmission range.

Interference may occur, resulting in incorrect data, if the computer is:

••Near a TV, PC, radio, motor, or in a car or train.

••Close to a railroad crossing, railway tracks, TV stations and/or radar base.

••Using with other wireless devices, or some particular battery lights.

Preparing the computer

Battery case cover

MENU

Pressure sensor

AC

MODE

SSE

km/h mph : Speed unit

: Wheel size icon

: Sensor signal reception icon

Operation of buttons when the computer is mounted on the bracket

Click

MODEMODE+SSE

Press only the computer	Press the SSE button with
body.	the computer body together.
	SSE button by itself does
	not function.

How to restart

After changing the battery, or when the computer displays an error, restart the com- puter according to the following procedure.

111 Press the AC button on the back of the computer. 222 Set the clock. Refer to “Preparing the computer 5”.

**The stored sea level altitude, home altitude, speed unit, wheel size, sensor ID, countdown dis- tance, selected wheel, AT setting, total distance and total altitude gain will not be changed after pressing the AC button.

How to install the unit on your bicycle

2	4	1 Bracket band
		2 Bracket
	5
1		3 Nut
3	7	4 Sensor
		5 Magnet

When using the computer for the first time or resetting to the factory default setting, format according to the following procedure.

1	Format (initialize)	MENU
	1. Press and hold the MENU button.

Tire circumference

reference table

ETRTO	Tire size	L (mm)
47-203	12x1.75	935
54-203	12x1.95	940
40-254	14x1.50	1020
47-254	14x1.75	1055

		6 Sensor rubber pad
6	8	7 Bracket rubber pad
		8 Nylon ties (x2)

Install the sensor and magnet

2.	Press the AC button.
3.	Release the AC button.	AC
4.	Release the MENU button.

2 Select the speed and temperature unit When MODE and SSE are pressed simultane- ously, “Speed unit” or “Temperature unit” can be selected. Select “km/h” or “mph” for the speed unit, and “°C” or “°F” for the temperature unit. Press MENU to register.

Switch the screen (By	Unit	Register
pressing simultaneously)	selection	the setting
MODE+SSE	MODE	MENU

3 Enter the tire circumference

40-305	16x1.50	1185
47-305	16x1.75	1195
54-305	16x2.00	1245
28-349 16x1-1/8		1290
37-349 16x1-3/8		1300
32-369	17x1-1/4	1340
	(369)
40-355	18x1.50	1340
47-355	18x1.75	1350
32-406	20x1.25	1450
35-406	20x1.35	1460
40-406	20x1.50	1490
47-406	20x1.75	1515
50-406	20x1.95	1565
28-451 20x1-1/8		1545
37-451 20x1-3/8		1615
37-501 22x1-3/8		1770
40-501 22x1-1/2		1785
47-507	24x1.75	1890
50-507	24x2.00	1925

AThe distance from the computer to the sensor is within the transmission range.

Max

70 cm

B	The magnet passes		C	The clearance between
	through the sensor zone.			the sensor and mag-
		Sensor zone		net is 5 mm or less.
				4
	S			NS
		ENSORE		S
				ZOOR
			5	E
		ZON		E
				N
	4 5			5mm
Right front fork (inside)

**The magnet may be installed anywhere on the spoke if the above installation conditions are satisfied.

Enter the tire circumference of your bicycle in mm.

**Refer to the tire circumference reference table.

Increase	Move digits (By press-	Register
the value	ing simultaneously)	the setting
MODE	MODE+SSE	MENU

4 Set the sensor ID

Hold the computer body close to the sensor (20 - 70cm), and press and hold the RESET but-

54-507	24x2.125	1965
25-520	24x1(520)	1753
	24x3/4	1785
	Tubuler
28-540	24x1-1/8	1795
32-540	24x1-1/4	1905
25-559	26x1(559)	1913
32-559	26x1.25	1950
37-559	26x1.40	2005
40-559	26x1.50	2010
47-559	26x1.75	2023
50-559	26x1.95	2050
54-559	26x2.10	2068
57-559	26x2.125	2070

1 Install the sensor		Right front fork	2 Install the magnet
	4	Pull securely	Spoke on the right
		8
	SEN	SENS	5
6	SOR	ONE
	ZONE
**Install the sensor to the front fork as high as possible.			To the sensor zone

ton on the sensor with a sharp object. Sensor will randomly generate an ID number for the computer body to receive, and displays on the screen. If successfully synchronized, screen will automatically move on to Clock setting screen.

**When setting the sensor ID, place the sensor at least 20 cm (approxi-

58-559	26x2.35	2083
75-559	26x3.00	2170
28-590 26x1-1/8		1970
37-590 26x1-3/8		2068
37-584 26x1-1/2		2100
	650C Tubuler	1920
	26x7/8
20-571	650x20C	1938
23-571	650x23C	1944

3Attach the bracket to the stem or handlebar

When attaching the bracket to the stem Stem

7

2 1

Caution:

Cut

mately 8 inches) away from the computer. Press and hold the RESET button, the sensor will send the ID when releasing the button.

**The computer is on standby for 5 minutes while setting the sensor ID. It dis- plays “ERROR”, and cancels the ID when no ID signal is received during the standby, or you press MODE and SSE simultaneously. Screen will move on to clock setting. Without the ID, speed cannot be detected and displayed. Be sure to set the sensor ID according to “Sensor ID setting” on the menu screen.

**Original ID is saved if you cancel the ID.

Start the ID set-	Cancel the ID or	Move to Clock
ting (By press-	reset (By pressing	Setting when no
RESET ing & holding)	MODE+SSE simultaneously)	MENU ID has been set

25-571	650x25C	1952
	26x1(571)
40-590	650x38A	2125
40-584	650x38B	2105
25-630	27x1(630)	2145
28-630	27x1-1/8	2155
32-630	27x1-1/4	2161
37-630	27x1-3/8	2169
18-622	700x18C	2070
19-622	700x19C	2080
20-622	700x20C	2086
23-622	700x23C	2096
25-622	700x25C	2105
28-622	700x28C	2136
30-622	700x30C	2146
32-622	700x32C	2155

When attaching the bracket to the handlebar

**On account of the receiving sensitivity, attach the bracket so that the computer is kept horizontal. Handlebar

7

1 2

Round off the cut edge of the bracket band to prevent injury.

3

Set the clock
5 When MODE and SSE are pressed simultane-
ously, “Displayed time”, “Hour”, and “Minute”
will appear, in this order.
Switch the screen	24h ↔ 12h,	Register
or move digits	or increase	the setting
(By pressing	MODE the value	MENU (Finish)
MODE+SSE simultaneously)

	700C	2130
	Tubuler
35-622	700x35C	2168
38-622	700x38C	2180
40-622	700x40C	2200
42-622	700x42C	2224
44-622	700x44C	2235
45-622	700x45C	2242
47-622	700x47C	2268
54-622	29x2.1	2288
60-622	29x2.3	2326

4 Remove/install the computer	**For wing type handlebar or oversized stem,
While supporting it by hand,	bracket can be mounted using the Bracket
Click	Holder and nylon ties. (Option)
	2

Measure wheel circumference (L) of your bike
To get the most accurate calibration do a wheel roll out. With the valve stem
perpendicular to the ground, mark the pavement at the valve stem. With the
riders weight on the bike, roll the wheel one tire revolution in a straight line
and mark the ground when the valve stem is perpendicular to the ground
again. Measure the distance in millimeters. This is the most accurate wheel	L mm
calibration number.

push it out as if lifting the front up

**After installation, check that the speed is displayed on the computer when gently turning the

front wheel. When it is not displayed, check the positions of A , B , and C .

1