Cateye CC-AT200W Starting/Stopping measurement, Sea level altitude correction, Countdown distance

Operating the computer [Measuring screen]

Starting/Stopping measurement			Current speed	Temperature........... The current temperature is displayed.
You can select the Auto mode (automatic mea-			0.0(4.0) – 105.9 km/h	**It is updated when the measurement screen is displayed (while measuring:
suring) or manual mode. During measurement,				every 3 seconds, while not riding: every 20 seconds).
			[0.0(3.0) – 65.0 mph]
				**The altitude measurement is updated every 3 seconds during measurement (when counting the
km/h or mph flashes. The maximum speed and
				elapsed time), but not updated when measurement stops.
total distance are updated regardless of start-
			Selected mode at	Caution:
ing/stopping measurement.
•• Auto mode (	on)		the middle display	When Auto mode is Off, elapsed time counts even if the bicycle is not in motion.
			Selected mode at	After measurement, be sure to press MODE and SSE simultaneously to stop measuring.
Measurements start automatically when the
				Sea level altitude correction
bicycle is in motion.			the bottom
•• Manual mode		: Pace arrow		This unit determines the altitude by converting the change in atmospheric pressure and tem-
When the computer is mounted on the				perature; therefore, it may cause deviation from the actual sea level altitude. It is recommended
bracket, start/stop measuring by pressing		Indicates whether the current speed is		to correct the sea level altitude just before measurement, using either the following methods.
		faster ( ) or slower ( ) than the average
the MODE and SSE buttons simultaneously.				•• ADJUST (sea level altitude correction): Enter the altitude at the current point.
		speed.
**For switching between Auto and Manual mode, refer		: Auto mode icon		Enter the actual value at the point where the sea level altitude is known,
to “Auto mode setting” on the menu screen.		: Low battery indicator of the computer		such as along the seashore, or at a sign on the mountain, etc.

Switching computer function					**Press and hold MODE and SSE simultaneously on the setting screen to reset the cor-
Pressing the MODE changes the middle/bottom row display.					rected value to the default (a value according to ISO2533).
		Measuring screen			•• HOME (home altitude setting): Preset a specific sea level altitude.
					Preset the sea level altitude at your home in advance. Move to the HOME screen,
Middle display		Bottom display			and then return to the measuring screen by pressing MENU or the relevant short-
					cut. Then, the sea level altitude changes to the preset value. You can start with the
					correct sea level altitude by setting home altitude before stating from your home.
	Temperature	Clock			**The sea level altitude is corrected on the menu screen “Sea level altitude correction”. Move to the sea
	-20 – 60 ˚C				level altitude correction screen by pressing MENU or the relevant shortcut from the measuring screen.
	[-4 – 140 ˚F]	0:00 – 23:59 or 1:00 – 12:59			Countdown distance
		Tm			Once the target trip distance is set, the unit displays the countdown distance to the target,
Sea Level Altitude					and notifies at arrival. When the unit reaches the target distance, the countdown distance
		Elapsed Time		Shortcut A
					appears and the value flashes. The screen returns to the original display in 5 seconds.
-500 ­– 9000 m		0:00’00” – 99:59’59”
[-1640 – 29600 ft]					**The target distance is set on the menu screen “Countdown distance setting”. Move to the countdown
	Slope (%)				distance setting screen by pressing MENU, MODE, or the relevant shortcut from the measuring screen.
		Dst		MODE
	-99% – +99%				Changing the computer settings [Menu screen]
		Trip Distance		(By pressing
		0.00 – 9999.99 km [mile]		& holding)	Pressing MENU on the measuring screen moves to the menu screen for setup change. Once in-
			Shortcut to sea level
					side the menu screen, press the MODE button to scroll through setup items. Press MODE+SSE to
			altitude correction.
		Dst 2			enter the edit screens. Change cannot be done if there is an incoming signal and timer is active.
			Valid while the com-
		Trip Distance-2	puter is receiving no		Shortcut	: When using a shortcut, the sea level altitude correction screen or the countdown distance setting
		0.00 – 9999.99 km [mile]	signal from sensor.				screen is not displayed as shown in the figure below. It moves directly to the edit screen.
					Sea level alti-
MODE
					tude correction			Wheel selection		Auto mode setting
*1		Av
		Average Speed*2
		0.0 – 105.9 km/h [0.0 – 65.0 mph]
							MODE	MODE	MODE	MODE
		Mx
	Ascending	Maximum Speed			MENU		Countdown distance setting		Wheel size entry
	Altitude	0.0(4.0) – 105.9 km/h [0.0(3.0) – 65.0 mph]								MODE
0 – 999999 m [ft]
								Sensor ID setting		Clock setting
				Shortcut B
		Countdown
		Distance
		9999.90 – 0.00 km [mile]		MODE	Menu
		Shortcut to countdown distance setting. Valid while		(By pressing	screen		MODE	MODE	MODE	MODE
		the computer is receiving no signal from sensor.		& holding)
		Odo				Speed/temperature unit selection			Total distance manual entry
	Total Altitude
		Total Distance					Setting change	**After changing, be sure to press MENU to register the setting.
0 – 99999	Gain
		0.0 – 9999.9 / 10000 – 999999 km [mile]					( b y p r e s s i n g	**If the setting screen is not touched for a minute, the measur-
/ 100 – 99999 x 1000 m [ft]
*** With the computer installed on the bracket, press on the four raised dots on the face of the computer.					MODE+SSE simultaneously)			ing screen appears without data changes.

*** If Tm exceeds approximately 27 hours or Dst exceeds 9999.99 km, .E (Error) is displayed as the			Sea level altitude correction
average speed. Reset data.			Shortcut A : MODE (By pressing & holding) → Back to the previous measuring screen
Resetting data			...................................	Select ADJUST (sea level altitude correction) or HOME (home altitude
While displaying any data other than Dst-2, pressing and holding the MODE and SSE				setting) by pressing MODE. When MODE and SSE are pressed simul-
				taneously,“+/- selection” or “Move digit” can be selected, and pressing
simultaneously resets the measurement data to 0. While displaying Dst-2, pressing and
				MODE increases the +/- selection or the value. Enter the desired altitude.
holding the MODE and SSE simultaneously resets only Dst-2to 0. In both cases, the
				**For details, refer to “Sea level altitude correction”.
total distance and total altitude gain are not reset.
			Countdown distance setting
Power-saving mode
			Shortcut B : MODE (By pressing & holding) → Back to the previous measuring screen
If the computer has not received a signal for 10 minutes, power-saving mode will activate and
				Pressing MODE increases the value and pressing MODE and SSE
only the clock will be displayed. When the computer receives a sensor signal again, the mea-			................................
				simultaneously moves to the next digit.
suring screen reappears. If 60 minutes’ inactivity elapses, power-saving mode will change to
			Wheel selection	Toggle between the specified wheel size (tire circumference)
SLEEP mode. Pressing the MODE in SLEEP mode brings up the measuring screen.
				and	. Use this function if the computer is to be shared between
Altitude measurement
				two bicycles. Pressing MODE toggles between		and	.
This unit detects the change		in atmospheric pressure and temperature using a pressure sensor	Wheel size entry ....	Pressing MODE increases the value and pressing MODE and SSE
built in the computer, and converts it to the altitude using the relation between the altitude and				simultaneously moves to the next digit. To enter the wheel size				,
pressure of ISO 2533 (Standard atmosphere), which was developed based on the international
				display	using “Wheel selection”.
standard atmosphere specified by the International Civil Aviation Organization (ICAO). Accord-
			Auto mode setting	Press MODE to select ON or OFF.
ingly, the measurements tend to change, even at the same point, according to the atmospheric
pressure due to the weather condition. Furthermore, the measurements may change more			Clock setting	Operate as described in “Preparing the computer 5”.
than 30 m from the early morning to the evening even under a stabilized weather condition.			Total distance manual entry
The measurements may be incorrect in the following place or environment.				Before re-initializing the computer, note the total distance. This
••When the atmospheric pressure and temperature change significantly due to a rapid			................................
				reading will later allow you to enter the total distance manually.
weather change.
				Pressing MODE increases the value and pressing MODE and SSE
••In the place where the atmospheric pressure is regulated, such as inside an airplane.
				simultaneously moves to the next digit.
••The altitude data may change temporarily when the temperature changes rapidly by get-
			Sensor ID setting....	Pressing MODE changes to ID1 or ID2, and pressing MODE and
ting out of a room, etc. It may return to a correct value after a while.
				SSE simultaneously moves to ID setting. Set the ID as described
Altitude measurement
				in “Preparing the computer 4”.
This unit has four altitude-related functions and temperature function.				**ID2 is used when the computer is shared with the second sensor installed
Sea level altitude The current sea level altitude is displayed.				to another bicycle. The computer will identify ID1 and ID2 automatically
				after waking up from Power-saving mode.
	**For effective use of the sea level altitude, refer to “Sea level altitude correction”.		Speed/temperature unit selection
Slope	Measures slope in percent unit, where 45 degree angle being 100%.
				Operate as described in “Preparing the computer 2”.
	**It is updated every 3 seconds, calculating from several times of the change in		................................

altitude and the trip distance. Slope update may be delayed. Abnormal data may also be temporarily displayed when speed quickly changes or during low-speed.

Ascending altitude... Accumulation of ascent from the reset point to the current point is displayed.

Total altitude gain ... The total altitude gain is displayed.

2