BICYCLE/FRAME INSTRUCTION GUIDE
TRANSITION CARBON - ALL MODELS
THIS INSTALLATION GUIDE CONTAINS IMPORTANT INFORMATION.
PLEASE READ CAREFULLY AND STORE IN A SAFE PLACE.
Congratulations! The Specialized bicycle you have chosen is among the finest of advanced composite products available in cycling. Carbon fiber is a very special material that requires particular care during assembly, storage and riding. This installation guide contains instructions and warnings, plus torque specifications.
Please read the following instructions. If you have any doubt regarding your mechanical ability and/or installation of this product, visit your local authorized dealer. Specialized recommends that components be installed on the frame using a torque wrench, by a qualified mechanic.
Please read the following Warnings. Because the failure to follow any Warning may result in a catastrophic failure of the frame, resulting in serious personal injury or death, this phrase may not be repeated in connection with each Warning.
To ensure the best assembly possible and to prevent any damage to the components or frame, follow all torque specifications. Please refer to the specific owner’s manual for mating component’s correct torque specifications. If the mating component’s recommended torque exceeds the frame’s recommended torque, use the lower torque spec. Due to torque considerations, not all components will be compatible.
Warning! Failure to follow the torque specifications in this installation guide will void the warranty, but most importantly may result in damage to the frame which may not be visible. If the frame is damaged, this can result in loss of structural integrity, which may result in serious personal injury or death.
Bicycle components such as a handlebar, handlebar stem, seat post, saddle, brakes, all must be compatible with each other, the frame and the intended use. Any doubt regarding compatibility should be discussed with your local authorized Specialized retailer.
Warning! When placing the frame and/or bicycle in a repair stand, clamp the stand using a frame clamp specifically designed for
INSTALLING THE SEAT POST & SADDLE
The Specialized Transition frames require a proprietary seat post, available in 3 different setbacks. The Transition seat post system allows for an extremely wide seat tube angle range which is infinitely variable inside that range, to help the rider achieve the optimal riding position.
To help the Transition frame achieve its aerodynamic benefits, the frame was designed with a very short seat post vertical adjustment range. Proper installation of the Transition Seat Post requires the use of a dedicated Transition Fit Kit tool set.
This setup (fitting and cutting) MUST be performed by an authorized Specialized dealer to ensure that the seat post is cut to the optimal length, to maximize the +/- vertical adjustment range.
Warning! Due to the nature of the seatpost having to be cut to a specific length, the seat post is NOT marked with a minimum insertion line. For proper seatpost insertion, ensure that the seat post extends below the minimum insertion hole located at the back of the seat tube area. Extension beyond the minimum insertion hole in the frame can result in failure.
Warning! Do not grease the seat tube surface that contacts the seat post. Grease reduces the friction that is critical to proper seat post grip. Remove any grease from the surfaces of the seat tube and seat post.
TECH TIP: Specialized recommends the application of carbon assembly compound between the seat tube and post to increase friction. Recommended compounds can be found at www.tacx.com. See your authorized Specialized retailer if you have any questions.
Tighten seat collar bolt to recommended torque of
Warning! Exceeding the specified recommended torque limit can result in damage to the seat post and/or frame.
ADJUSTING THE SEAT POST
•Install the seat post into the seat tube (fig.1).
•Install the rail clamp carrier in the chosen direction (reversible) and tighten the alloy rail carrier bolt (bolt #1, fig.2).
•Grease the contact surfaces and bolt threads of the rail clamp Mechanism, then install it in the rail clamp carrier.
•Install the saddle in the rail clamp mechanism.
•Adjust the saddle to the desired height, angle and
•Torque the rail clamp bolt to the recommended setting. To avoid damage, the nut tab must be properly lined up with the rail clamp slot (bolt #2, fig.2).
•Torque the seat collar bolt to the recommended setting (fig.1).
GENERAL WARNINGS
FORK: Do not remove the small bumpers on the side/back of the fork legs. These are to protect the frame from fork contact.
REAR WHEEL: Due to variables in tire manufacture, heat expansion, foreign debris, etc. Specialized recommends a minimum rear wheel-
Thread the horizontal dropout screws in or out to
Contact between the frame and tire can cause wear and damage to the frame, which can result in failure.