NordicTrack NTTL24992 user manual Trouble-Shooting, Problem The power turns off during use, Top

Page 26

TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

 

On

 

Position

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. Make sure that the on/off switch is in the on position.

e. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the indicated Screws (3) from the Hood (37). Carefully rotate and lift the Hood.

b. Locate the Reed Switch (20) and the Magnet (107) on the left side of the Pulley (10). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw

(109)and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

a

3

37

 

 

 

3

b

 

 

 

1/8”

 

 

109

10

 

20

107

 

 

 

Top

 

 

View

 

26

Image 26
Contents Customer HOT Line QUESTIONS?Model No. NTTL24992 Serial No Table of Contents Important Precautions Page Right Side Before YOU BeginLeft Side Assembly Not tighten the Bolts yet Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Getting Started Move the on/off switch to the on positionEnter your weight Attach the clip to the waistband of your clothesChange the incline of the treadmill as desired HOW to USE the Manual ModeSelect the manual mode Training Zone disSpeed/Pace-The right side of the main HOW to USE Preset ProgramsSelect the desired preset program Measure your heart rate, if desiredMeasure your heart rate if desired When the program has ended, remove the keyFollow your progress with the displays Remove the key HOW to Create Custom ProgramsSelect one of the custom programs HOW to USE Custom Programs Select the fitness test program HOW to USE the Fitness Test ProgramPut on the chest pulse sensor Enter your ageHOW to USE the PULSE-DRIVEN Program Select the pulse-driven programRefer to on HOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerPressVCR. the Play button on your CD player or HOW to Connect Your VCRAudio Adapter Cable Whenkey. the program is completed, remove HOW to USE Programs Directly from OUR Internet Site Follow the on-line instructions to start the programInformation MODE/DEMO Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETop TROUBLE-SHOOTINGProblem The power turns off during use Problem The walking belt slows when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Suggested Stretches R1200A Qty DescriptionOrdering Replacement Parts NTTL24992 DRAWING-Model No Limited Warranty