NordicTrack NTTL09990 user manual Do not tighten the Bolts yet

Page 7

4.Insert two Handrail Bushings (75) into the right Upright

(69).Turn the Handrail Bushings so they fit on the Upright with the thick half of the Bushings inwards as shown in the inset drawing.

Insert two Handrail Bolts (78) with Handrail Washers

(77)into the Handrail Bushings (75), the right Upright (69), and the right Handrail Spacer (65). Lift up the right Handrail (66) to align the Bolts with the holes in the Handrail. Next, thread the Bolts into the Handrail (66).

Do not tighten the Bolts yet.

Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).

5.Press the Lock Knob Sleeve (70) into the left Upright (69).

Make sure that the Lock Pin Collar (72) and the Spring (71) are on the Lock Pin. Insert the Lock Pin into the left Upright (69). Press the Lock Knob Spacer (117) onto left Upright. Tighten the Lock Knob (68) onto the Lock Pin.

6.Look at the Endcap (58). If the left or right foot on the Endcap does not touch the floor, the included thick base pads should be attached to the treadmill as de- scribed below.

Refer to assembly step 2. Lower the treadmill frame and the Uprights (69) as shown. If the left foot of the Endcap (58) was off the ground, remove the two Base Pads (99) from the right Upright (69). Attach the in- cluded thick base pads to the Upright. If the right side of the Endcap was off the ground, attach the thick base pads to the left Upright.

Note: If either side of the Endcap (58) lifts off the floor when the treadmill is used, attach the thick base pads as described.

4

 

 

 

66

 

 

65

 

 

69

 

 

75

 

 

77

Thick

 

Half

 

 

75

 

 

77

78

 

5

 

 

 

69

 

68

 

 

 

70

 

117

71

 

72

 

 

 

 

 

74

6

 

 

Foot

 

 

58

 

 

 

 

Foot

7.Make sure that all parts are tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the face of the hood decal and the “ComforTrack” decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or car- pet from damage, place a mat under the treadmill.

7

Image 7
Contents Model No. NTTL09990 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Left Side Before YOU BeginRight Side Your own phillips screwdriver AssemblyDo not tighten the Bolts yet HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Getting Started HOW to USE the Manual Mode On the foot rails and place your HOW to USE Preset ProgramsSelect one of the three preset programs Measure your heart rate, if desiredFollow your progress with the displays When the program has ended, remove the keySelect one of the custom programs HOW to Create Custom ProgramsRemove the key HOW to USE Custom Programs HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAudio Adapter Cable HOW to Connect Your VCRPressVCR. the Play button on your CD player or Whenkey. the program is completed, remove Follow your progress with the LED track DisplaysFollow the on-line instructions to start Program HOW to USE Programs Directly from OUR Internet SiteReturn to the treadmill and stand on the foot Optional Hand Weights Information MODE/DEMO ModeOptional Chest Pulse Sensor HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TROUBLE-SHOOTINGTop View Problem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Key No. Qty Description R0200AQty Description Ordering Replacement PartsExploded DRAWING-Model No. NTTL09990 118 Limited Warranty