Maintenance and Troubleshooting, Assembly

MAINTENANCE AND TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See page 7.) If an ex- tension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrench and your own phillips screwdriver			,
adjustable spanners	, and 9/16” socket spanner	.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill
c. Check the circuit breaker located on the treadmill	c
near the power cord. If the switch protrudes as	c
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
shown, the circuit breaker has tripped. To reset the		Tripped	Reset
circuit breaker, wait for five minutes and then press		Tripped	Reset


the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call our Customer Service Department.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. UNPLUG THE POWER CORD. Check the batteries in the console (see assembly step 7 on page 6). Most problems are the result of drained batteries.

b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood, and carefully remove the hood.

WARNING: Do not plug in the power cord until the treadmill is completely assembled.

1.Using two adjustable spanners, attach the Wheels (15) to the Base (71) with the two Wheel Bolts (14) and the two Wheel Nuts (42) as shown. Do not overtighten the

Wheel Bolts; the Wheels should turn freely.

2.With the help of a second person, carefully raise the Right and Left Handrails (6, 7) to the position shown.

1	42	15
		15
		14
		14
		14	15
		71
			42
2
		7
			6

Locate the Reed Switch (46) and the Magnet (49) on the left side of the Pulley (53). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Screw (26) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

3 mm

Top View

53 49

3.With the help of a second person, carefully tip the tread- mill onto its left side. Hold the Base (71) against the Right Handrail (6) and the Left Handrail (not shown). Make sure that the Wheels (15) are toward the front of the treadmill as shown.

Using a 9/16” socket spanner, attach the Base (71) to the Right Handrail (6) with two Handrail Bolts (12), two Handrail Washers (31), and two Handrail Nuts (17). Do not tighten the Handrail Nuts yet. Attach the Base to the Left Handrail (not shown) in the same way. Tighten all four Handrail Nuts.

312

1517

Tip the treadmill back to the position shown in step 1.