Healthrider HRTL34306.1 manual

Page 9

7.Set the Console Assembly (91) face-down on a soft surface to avoid scratching the Console Assembly. Hold the Right Handrail (33), which has a large hole in the location shown, near the Console.

Next, insert the console wire into the hole in the side of the Right Handrail (33). Using needlenose pliers, pull the console wire out of the hole near the bracket on the Right Handrail.

Then, set the Right Handrail (33) on the Console Assembly (91). Make sure that no wires are pinched. Finger tighten a Crossbar Screw (85) with a Crossbar Star Washer (7) into the Right Handrail, and then start two Console Screws (10) into the Right Handrail. Tighten the

Crossbar Screw and then the two Console Screws; do not overtighten the Screws.

Attach the Left Handrail (not shown) to the Console Assembly (91) in the same way. Note: There are no wires on the left side.

8.See drawing 8a. Press the indicated tab and re- move the guard from the console wire with needlenose pliers. Discard the guard.

With the help of a second person, hold the Console Assembly (91) near the Right Upright (54).

Remove the colored tie from the Wire Harness (39). Connect the Wire Harness to the console wire. Make sure to connect the connectors properly (see drawing 8b). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the connectors and excess wire into the Right Upright (54).

7

 

 

 

 

Console

85

 

 

Wire

 

 

 

 

 

Bracket

7

10

 

 

33

Large

 

 

Hole

 

 

 

 

 

 

91

 

 

8

 

 

8a

 

Console

 

Wire

91

Tab

 

 

Guard

Console

 

Wire

8b

39

 

54

39

 

9. Attach the Console Assembly (91) to the Right

9

91

 

Upright (54) and the Left Upright (53) with four

 

 

 

 

 

 

four Handrail Bolts (8) and four Handrail Star

 

 

 

Washers (5). Make sure that no wires are

 

 

 

pinched. Start all four Handrail Bolts before

 

 

 

tightening them.

 

 

 

With the help of a second person, carefully lower

 

 

 

the Uprights (53, 54) to the floor.

 

 

 

 

 

8

8

 

 

5

5

 

 

54

53

 

9

 

 

Image 9
Contents QUESTIONS? Model No. HRTL34306.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Make sure that the power cord is unplugged AssemblyPage Washer 9 do not tighten the Colored Patch Frame Bolt yet Outer side of the Frame Spacer facingPage Top View Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual Mode Measure your heart rate if desired HOW to USE a Speed Program Select one of the four speed programsWhenkey. you are finished exercising, remove HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use Maintenance and TroubleshootingProblem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description R0806AOrdering Replacement Parts Exploded Drawing A-Model No. HRTL34306.1 R0806A Exploded Drawing B-Model No. HRTL34306.1 R0806A Exploded Drawing C-Model No. HRTL34306.1 R0806A Exploded Drawing D-Model No. HRTL34306.1 R0806A Limited Warranty